Manual Bosch UniversalImpact 7000 (page 22 of 127) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

708164

Zoom out

Zoom in

1/127

22 | English

(1) by turning the hex key (27) in the rotational direction .

A tightly seated keyless chuck is loosened with a light blow

on the long shaft of the hex key (27). Remove the hex key

from the keyless chuck and completely unscrew the keyless

chuck from the power tool.

Fitting the drill chuck (seefigureL)

To assemble the keyless chuck (1), perform the same steps

in reverse order.

u After successfully fitting the drill chuck, remove the

steel pin from the hole again.

The drill chuck must be tightened using a tight-

ening torque of approx. 30–35 Nm.

Operation

Starting Operation

u Pay attention to the mains voltage. The voltage of the

power source must match the voltage specified on the

rating plate of the power tool. Power tools marked

with 230V can also be operated with 220V.

u Products that are only sold in AUS and NZ: Use a resid-

ual current device (RCD) with a nominal residual current

of 30 mA or less.

Set the rotational direction (see figureM)

The rotational direction switch (4) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (6) is being pressed.

Right rotation: To drive in screws and tighten nuts, press

the rotational direction switch (4) through to the left stop.

Left Rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (4) through to the right

stop.

Setting the Operating Mode

Drilling and screwdriving

Set the selector switch (3) to the "drilling"

symbol.

Impact drilling

Set the selector switch (3) to the "impact

drilling" symbol.

The selector switch (3) clicks into place and can also be ac-

tuated when the motor is running.

Switching on/off

To start the power tool, press and hold the on/off switch

(6).

Press the lock-on button (5) to lock the on/off switch (6) in

this position.

To switch off the power tool, release the on/off switch (6);

or, if the switch is locked with the lock-on button (5), briefly

press the on/off switch (6) and then release it.

Rapid shut-off (Kickback Control) (UniversalImpact 800)

The emergency switch-off function (Kick-

Back Control) gives the user greater control

over the power tool and offers them better

protection than power tools that do not

have KickBack Control. The power tool will switch off if it

suddenly and unforeseeably rotates around the drilling

axis.

To switch the tool back on, release the on/off switch and

then press it again.

u If the KickBack Control function is defective, it will no

longer be possible to switch the power tool on. Have

the power tool serviced by a qualified repair person

using only original replacement parts.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when

it is on by pressing in the on/off switch (6) to varying ex-

tents.

Applying light pressure to the on/off switch (6) results in a

low rotational speed/impact rate. Applying increasing pres-

sure to the switch increases the speed/impact rate.

Preselecting the speed/impact rate

You can preselect the required speed/impact rate using the

speed preselection thumbwheel (7), even during operation.

The required speed/impact rate is dependent on the mater-

ial and the work conditions and can be determined by prac-

tical trials.

Working Advice

u Pull the plug out of the socket before carrying out any

work on the power tool.

u Only apply the power tool to the screw/nut when the

tool is switched off. Rotating tool inserts can slip off.

After working at a low speed for an extended period, you

should operate the power tool at the maximum speed for ap-

proximately three minutes without load to cool it down.

Removing the Dust Collection Device (seefiguresN–P)

It is a good idea to remove the dust collection device(13):

– In order to use the rail of the Drill Assistant(10) as a

depth stop

– When using large application tools (e.g. holesaw or twist

drill bit)

Maintenance and Service

Maintenance and Cleaning

u Pull the plug out of the socket before carrying out any

work on the power tool.

u To ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

In order to avoid safety hazards, if the power supply cord

needs to be replaced, this must be done by Bosch or by an

after-sales service centre that is authorised to repair Bosch

power tools.

1 609 92A 57D | (29.11.2019) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch UniversalImpact 7000 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch UniversalImpact 7000 Manual

Product: