Manual Bosch UniversalImpact 18 (page 12 of 181) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

708157

Zoom out

Zoom in

1/181

12 | English

u Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

of injury.

u Do not expose a battery pack or tool to fire or excess-

ive temperature. Exposure to fire or temperature above

130°C may cause explosion.

u Follow all charging instructions and do not charge the

battery pack or tool outside the temperature range

specified in the instructions. Charging improperly or at

temperatures outside the specified range may damage

the battery and increase the risk of fire.

Service

u Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

u Never service damaged battery packs. Service of bat-

tery packs should only be performed by the manufacturer

or authorized service providers.

Safety Warnings for Drills

Safety instructions for all operations

u Wear ear protectors when impact drilling. Exposure to

noise can cause hearing loss.

u Hold the power tool by insulated gripping surfaces,

when performing an operation where the cutting ac-

cessory or fasteners may contact hidden wiring. Cut-

ting accessory contacting a "live" wire may make exposed

metal parts of the power tool "live" and could give the op-

erator an electric shock.

Safety instructions when using long drill bits

u Never operate at higher speed than the maximum

speed rating of the drill bit. At higher speeds, the bit is

likely to bend if allowed to rotate freely without contact-

ing the workpiece, resulting in personal injury.

u Always start drilling at low speed and with the bit tip

in contact with the workpiece. At higher speeds, the bit

is likely to bend if allowed to rotate freely without contact-

ing the workpiece, resulting in personal injury.

u Apply pressure only in direct line with the bit and do

not apply excessive pressure.Bits can bend causing

breakage or loss of control, resulting in personal injury.

Additional safety warnings

u Switch the power tool off immediately if the applica-

tion tool becomes blocked. Be prepared for high

torque reactions which cause kickback. The applica-

tion tool becomes blocked when it becomes jammed in

the workpiece or when the power tool becomes over-

loaded.

u Hold the power tool securely. When tightening and

loosening screws be prepared for temporarily high torque

reactions.

u Secure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure than by

hand.

u Use suitable detectors to determine if there are hid-

den supply lines or contact the local utility company

for assistance. Contact with electric cables can cause

fire and electric shock. Damaging gas lines can lead to ex-

plosion. Breaking water pipes causes property damage.

u Always wait until the power tool has come to a com-

plete stop before placing it down. The application tool

can jam and cause you to lose control of the power tool.

u In case of damage and improper use of the battery, va-

pours may be emitted. The battery can set alight or ex-

plode. Ensure the area is well ventilated and seek medical

attention should you experience any adverse effects. The

vapours may irritate the respiratory system.

u Do not open the battery. There is a risk of short-circuit-

ing.

u The battery can be damaged by pointed objects such

as nails or screwdrivers or by force applied externally.

An internal short circuit may occur, causing the battery to

burn, smoke, explode or overheat.

u Only use the battery with products from the manufac-

turer. This is the only way in which you can protect the

battery against dangerous overload.

Protect the battery against heat, e.g. against

continuous intense sunlight, fire, dirt, water

and moisture. There is a risk of explosion and

short-circuiting.

Product Description and

Specifications

Read all the safety and general instructions.

Failure to observe the safety and general in-

structions may result in electric shock, fire

and/or serious injury.

Please observe the illustrations at the beginning of this oper-

ating manual.

Intended use

The power tool is intended for tightening and loosening

screws, as well as for drilling in wood, metal and plastic and

for impact drilling in brick and masonry.

Product Features

The numbering of the product features refers to the diagram

of the power tool on the graphics page.

(1)

Tool holder

(2)

Keyless chuck

(3)

Torque presetting ring

(4)

Mode selector switch

(5)

Gear selector switch

(6)

Battery release button

(7)

Battery

(8)

Rotational direction switch

(9)

On/off switch

1 609 92A 4Y3 | (23.04.2019) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch UniversalImpact 18 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch UniversalImpact 18 Manual

Product: