795171

Bosch UniversalDistance 50 Manual

24
Zoom out
Zoom in
Previous page
1/399
Next page
24 | English
Measuring process
Once switched on, the measuring tool is in the length measurement
function. Other measuring functions can be set by repeatedly press-
ing the (3) button or the navigation buttons (7) [+] or (2) [–] (see
"Measuring functions", page24).
Once the measurement function is selected by pressing the measur-
ing button (4), the laser beam is switched on.
Once the measuring tool has been switched on, the rear edge of the measuring tool is se-
lected as the reference level for measurement. To change the reference level, select (see
"Selecting the reference level (see figures A–B)", page24).
Place the measuring tool at the line you want to measure from (e.g. wall) with the refer-
ence level selected.
To initiate the measurement, briefly press the measuring button (4). Afterwards, the
laser beam is switched off. To switch the laser beam on again, briefly press the measur-
ing button (4). To initiate a further measurement, briefly press the measuring button (4)
again.
uDo not direct the laser beam at persons or animals and do not stare into the laser
beam yourself (even from a distance).
In the continuous measurement function, measurement will begin after the first press of
the measuring button (4).
The measured value typically appears within 0.5 seconds and no later than 4 seconds.
The duration of the measurement depends on the distance, the lighting conditions and
the reflective properties of the target surface.
If no measurement has been performed within approx. 20seconds of aim being taken,
the laser beam is switched off automatically to preserve battery life.
Selecting the reference level (see figures A–B)
You can choose between two different reference levels for the measurement:
– The rear edge of the measuring tool (e.g. when placing against walls).
– The front edge of the measuring tool (e.g. when measuring from a table edge).
To change the reference level, press the (1) button until the required reference level is
shown on the display. The rear edge of the measuring tool is pre-set as the reference
level every time the measuring tool is switched on.
Measuring functions
Measuring length
Select the length measurement function (see "Measuring process", page24).
1 609 92A 7LP | (02.05.2022) Bosch Power Tools
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch UniversalDistance 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch UniversalDistance 50 in the language / languages: All languages as an attachment in your email.

The manual is 3.87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info