708250
17
Zoom out
Zoom in
Previous page
1/290
Next page
English | 17
Bosch Power Tools F 016 L81 568 | (26.4.17)
Working Advice
General
Ensure that the pressure washer is on level ground.
Do not overreach with the high pressure hose or move the
pressure washer by pulling the hose, this could cause the ma-
chine to become unstable and fall over.
Do not kink or drive a motor vehicle over the high pressure
hose. Do not expose the high pressure hose to sharp edges or
corners.
Never use a roto nozzle or pencil jet to clean motor vehi-
cles.
Working advice for cleaning with detergents
Only use cleaning agents suitable specifically for high
pressure washers.
We recommend that you use detergent sparingly for the sake
of the environment. Observe the recommended dilution on
the detergent label.
The high-pressure foam nozzle supplied with this product in-
cludes a regulator to control detergent use. Adjust as re-
quired.
Recommended cleaning method
Step 1: Select the fan jet setting on the 3 in 1 nozzle and re-
move the heavy dirt.
Step 2: Attach the foam bottle and spray on the detergent
sparingly.
Step 3: Rinse off the loosened dirt and detergent using the
fan jet setting on the 3 in 1 nozzle.
Note: When cleaning vertical surfaces, apply the detergent
from bottom to top. When rinsing off, work from top to bot-
tom.
Use with alternative water sources
The power washer is self-priming and enables water to be
drawn in from containers or natural water sources. It is IM-
PORTANT that the water filter is in clean condition when in-
serting it at the water inlet, and that only clean water is drawn
in.
Open tanks/containers and natural water sources
Use the Self Priming accessory kit comprising:
Inlet strainer with non return valve
–3m reinforced supply hose
Universal coupling to the pressure washer
This enables the pressure washer to draw water up to 0.5 m
above the water level in the source in approximately 15 sec-
onds.
Fully immerse the 3 m hose into the water to displace the air
in the hose. Connect the 3 m hose to the power washer and
make sure that the inlet strainer remains under water.
With the spray gun removed, switch the power washer on and
operate it until water flows uniformly out of the high-pressure
hose. If no water is coming out of the high-pressure hose after
25 seconds, switch the power washer off and check all con-
nections. As soon as water flows out of the high-pressure
hose, switch the power washer off and connect the spray gu-
nand spray lance to begin with the work.
It is important that hose and couplings are of good quality and
are tightly connected, and that the seals are undamaged and
properly inserted. Loose connections can impede the priming
(drawing in).
Water Tanks with outlet connections
When connecting the pressure washer to a water tank with a
suitable tap outlet, first connect the supply hose (not provid-
ed) to the tank outlet, open the tap to allow the water to dis-
place all the air in the hose and then connect to the pressure
washer.
Troubleshooting
Problem Possible Cause Corrective Action
Motor refuses to start Plug not connected Connect plug
Mains socket faulty Use another socket
Fuse faulty/blown Replace fuse
Extension cable damaged Try without extension cable
Motor protector has activated Allow to cool for 15 minutes
Frozen Wait for pump/water supply hose/accessory to
thaw
Motor stops Fuse faulty/blown Replace fuse
Motor protector has activated Allow to cool for 15 minutes
Wrong mains voltage Check that mains voltage corresponds to specifica-
tions on the model tag
Fuses blow Fuses incorrectly rated Change to a mains supply higher than the pressure
washer amp consumption
Motor starts but no pressure Nozzle partly blocked Clean nozzle
OBJ_BUCH-2981-002.book Page 17 Wednesday, April 26, 2017 3:49 PM
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch UniversalAquatak 125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch UniversalAquatak 125 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info