Manual Bosch Universal Saw 18V 100 (page 18 of 257) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian)

766851

Zoom out

Zoom in

1/257

18 | English

Note: The battery is supplied partially charged. To ensure

full battery capacity, fully charge the battery in the charger

before using your power tool for the first time.

The lithium-ion battery can be charged at any time without

reducing its service life. Interrupting the charging process

does not damage the battery.

The lithium-ion battery is protected against deep discharge

by the "Electronic Cell Protection (ECP)". When the battery

is discharged, the power tool is switched off by means of a

protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the

power tool has automatically switched off. The battery

can be damaged.

To remove the battery (4), press the release button (5) and

pull the battery upwards and out of the power tool. Do not

use force to do this.

Battery charge indicator

The battery charge indicator (3) indicates the charge condi-

tion of the battery when the power tool is switched on. It

consists of three green LEDs.

LEDs Capacity

3 × continuous green light 66–100%

2 × continuous green light 33–66%

1 × continuous green light 11–33%

1 x slowly flashing green light 0–10%

The three LEDs in the battery charge indicator (3) flash

quickly when the temperature of the battery is outside the

operating temperature range of −20 to +50°C and/or the

overload protection has been triggered.

Inserting/changing the saw blade

uWhen fitting or changing the saw blade, wear protect-

ive gloves. Blades are sharp and can become hot when

used for prolonged periods of time.

Selecting the saw blade

You will find an overview of recommended saw blades at the

end of these operating instructions. Only use saw blades

with a single lug shank (T shank) or with a 1/4" universal

shank (U shank). The saw blade should not be longer than

required for the intended cut.

Use a narrow saw blade when sawing tight curves.

Inserting the saw blade (seefigure A)

uClean the shaft on the saw blade before inserting it.

Adirty shaft cannot be securely fixed in place.

If necessary, remove the hood(9).

Push the saw blade receptacle (15) upwards in the direction

of the arrow. Push the saw blade (11), with the teeth in the

cutting direction, into the saw blade receptacle as far as it

will go.

Make sure when inserting the saw blade that the back of the

saw blade is in the groove on the guide roller (13).

uCheck that the saw blade is seated securely. A loose

saw blade can fall out and lead to injuries.

Removing the saw blade (seefigure B)

Push the saw blade receptacle (15) upwards in the direction

of the arrow and remove the saw blade (11).

Saw blade storage compartment (accessory) (see

figureC)

You can keep up to six saw blades that are no longer than

110mm in the saw blade storage compartment (18). Insert

the saw blades with single lug shank (T shank) into the saw

blade storage compartment in the recess intended for these.

You can place up to three saw blades on top of each other.

Close the saw blade storage compartment and push it as far

as it will go into the recess in the base plate (7).

Glide shoe (seefigureD)

When machining sensitive surfaces, you can place the glide

shoe (19) on the base plate (7) in order to prevent the sur-

face from being scratched.

To position the glide shoe (19), hook it to the front of the

base plate (7), push it up at the back and allow it to click into

place.

When working with the glide shoe, neither the saw blade

storage compartment(18) nor the CutControlmust be

used.

Anti-splinter guard (see figureE)

The anti-splinter guard (20) (accessory) can prevent splin-

tering of the surface while sawing wood. The anti-splinter

guard can only be used with certain saw blade types and only

at a cutting angle of 0°. When sawing with the anti-splinter

guard, the base plate (7) must not be moved to the rear for

sawing close to edges.

Push the anti-splinter guard (20) into the base plate (7)

from below (as shown in the figure with the groove facing up-

wards).

CutControl

CutControl enables the power tool to be guided precisely

along a cutting line marked on the workpiece. CutControl

includes the viewing window (12) with cut marks and the

base (10) for securing to the power tool.

Securing CutControl to the base plate (see figure F)

Firmly insert the viewing window for CutControl (12) into

the brackets on the base (10). Then push the base together

gently and allow it to click into place in the guide (21) on the

base plate (7).

Dust/Chip Extraction

The dust from materials such as lead paint, some types of

wood, minerals and metal can be harmful to human health.

Touching or breathing in this dust can trigger allergic reac-

tions and/or cause respiratory illnesses in the user or in

people in the near vicinity.

Certain dusts, such as oak or beech dust, are classified as

carcinogenic, especially in conjunction with wood treatment

additives (chromate, wood preservative). Materials contain-

ing asbestos may only be machined by specialists.

1 609 92A 5Y0 | (27.05.2021) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Universal Saw 18V 100 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 6,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch Universal Saw 18V 100 Manual

Product: