388878
21
Zoom out
Zoom in
Previous page
1/130
Next page
English | 21
Bosch Power Tools 2 609 003 546 | (18.11.10)
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in
connection with wood-treatment additives
(chromate, wood preservative). Materials
containing asbestos may only be worked by
specialists.
Provide for good ventilation of the work-
ing place.
It is recommended to wear a P2 filter-
class respirator.
Observe the relevant regulations in your
country for the materials to be worked.
Operation
Starting Operation
Setting the Operating Mode
With the selector switch for drilling/hammer
drilling 4, the operating mode of the machine is
selected.
Note: Change the operating mode only when the
machine is switched off! Otherwise, the ma-
chine can be damaged.
To change the operating mode, turn the selector
switch for “drilling/hammer drilling” 4 to the re-
quested position.
Reversing the Rotational Direction
(see figure D)
f Actuate the rotational direction switch 8
only when the machine is at a standstill.
The rotational direction switch 8 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 9 actuated.
Right Rotation: For drilling and driving in
screws, push the rotational direction switch 8
left to the stop.
The indicator for right rotation 6 lights up
when the On/Off switch 9 is actuated
and the motor is running.
Left Rotation: For loosening and unscrewing
screws and nuts, press the rotational direction
switch 8 through to the right stop.
The indicator for left rotation 7 lights up
when the On/Off switch 9 is actuated
and the motor is running.
Switching On and Off
To start the machine, press the On/Off switch 9
and keep it pressed.
To switch off the machine, release the On/Off
switch 9.
For low temperatures, the power tool reaches
the full hammer/impact capacity only after a cer-
tain time.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on pow-
er tool can be variably adjusted, depending on
how far the On/Off switch 9 is pressed.
Light pressure on the On/Off switch 9 results in
low speed/impact rate. Further pressure on the
switch increases the speed/impact rate.
Battery Charge-control Indication
The battery charge-control indicator 5 indicates
the charge condition of the battery for a few sec-
onds when the On/Off switch 9 is pressed
through halfway of fully.
Temperature Dependent Overload Protection
When using as intended for, the power tool can-
not be subject to overload. When the load is too
high or the allowable battery temperature of
70 °C is exceeded, the electronic control
switches off the power tool until the tempera-
ture is in the optimum temperature range again.
Additionally, the battery charge-control indica-
tor 5 flashes green and red at the same time un-
til the On/Off switch 9 is released.
Position for hammer drilling in con-
crete or stone
Position for drilling without impact
in wood, metal, ceramic and plastic
as well as for screwdriving
LED Capacity
Continuous lighting, green
> 30%
Continuous lighting, red
30%
OBJ_BUCH-605-004.book Page 21 Thursday, November 18, 2010 2:35 PM
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch uneo at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch uneo in the language / languages: English, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info