Manual Bosch Tronic TR2000TF (page 10 of 20) (English, German)

780663

Zoom out

Zoom in

1/20

Installation instructions

TR2000TF – 6 720 875 992 (2021/08)

• The installation instructions of the safety group must be followed.

• Only a prototype-tested diaphragm safety valve may be installed.

• A shutoff valve must not be installed between the safety valve and

floor-standing water heater.

• The safety valve must be operated regularly to verify its function and

prevent it from becoming blocked, e.g. by limescale deposits.

• This appliance can be used by children aged 8 years and older as well

as by persons with diminished bodily, sensory or mental perception,

or those who lack knowledge or experience, if they are monitored

or have received instruction concerning use and comprehend the

possible dangers that can result. Children may not play with the

appliance. Cleaning and maintenance by the user may not be

performed by unsupervised children.

• Keep children away from the appliance.

• Please monitor children to ensure that they do not play with the

appliance.

• The mixer and the warm water pipe may be hot. Please inform and in-

struct children appropriately.

• Do not use aggressive or abrasive cleaning detergents!

• Do not use a steam cleaner.

CAUTION:

DANGER Scalding!

▶Hot water may escape during draining.

If the appliance needs to be drained for maintenance or to protect the

whole installation when there is a risk of frost, proceed as follows:

• Close the shut-off valve in the cold water line.

• Open the hot water taps on all draw-off points.

• Drain the appliance using the drain valve.

Congratulations on purchasing this appliance. You have acquired a top-

quality product, which will give you a lot of enjoyment.

Please read this installation and operating instruction manual

carefully, then act accordingly! Store for future reference.

2 Installation instructions

Install the floor-standing water heater as described in the illustrated

section. Observe the instructions in the text.

The illustrations can be found at the end of the instruction manual.

2.1 Installation

For economic reasons the installation location should be near the most

frequently used tap connection.

2.1.1 Description of the appliance

The interior of the steel tank has been specially enamelled to prevent

corrosion and has been fitted with a protective anode. This anode

protects the inside of the cylinder from corrosion. The exterior has been

directly insulated with foam which cannot be removed. Cover the

appliance with the supplied protective jacket only when the installation

work is complete.

The universal flange enables electrical connections for single or double

circuit operation.

Single circuit operation

The appliance automatically heats up at any temperature setting subject

to the availability of power.

Dual circuit operation

During off-peak tariff periods (cheap rate periods of power supply

utilities), the appliance automatically heats up the water content with

standard heating output at any temperature settings. In addition, you

can start the booster heater during peak tariff periods.

Circulation pipes should be avoided on account of the high heat losses.

The circulation connection is located where the thermal insulation is

noticeably indented.

Parts supplied (Fig. 1 )

1 Floor-standing water heater

2 Protective jacket

Appliance design (Fig. 2 )

3 Hot-water outlet

4 Protective anode

5 Circulation connection piece

6 Mark for circulation connection piece

7 Steel tank, enamelled interior

8 Thermal insulation

9 Temperature selector switch

10 Push-button

11 Heating flange

12 Cold-water inlet

Dimensions (Fig. 3 )

Water connection (Fig. 4 )

• Comply with DIN 1988 and the regulations issued by the water

company.

Materials for cold-water and hot-water pipes

Water pipe made of steel, copper or plastic.

If plastic pipes are used, only install pipe systems made of crosslinked

polyethylene (high-density polyethylene) according to DIN 16893 series

2 (20 bar), checked in accordance with DVGW work sheets W 531 and

W 532 with the corresponding DVGW mark of conformity.

Information regarding the suitability and quality of other plastic pipes

without the above-mentioned design approval information can only be

provided by the pipe manufacturer.

Copper pipes are recommended if there is a risk of corrosion.

If using copper and steel materials, they must be joined in the following

sequence, as seen from the flow of direction: Copper comes after steel.

This will avoid corrosion by local cell formation.

Stipulated combinations:

• Cold-water pipe made of copper: hot-water pipe made of copper or

plastic

• Cold-water pipe made of steel: hot-water pipe made of steel, copper

or plastic

• Cold-water pipe made of plastic: hot-water pipe made of steel,

copper or plastic

Pressure reducing valve

The floor-standing water heater is designed to operate at pressures not

exceeding 0,6 MPa (6 bar). A pressure reducing valve must be situated

in the cold-water pipe if the water mains pressure exceeds 0,5 MPa (5

bar). If the water mains pressure exceeds 1,0 MPa (10 bar), a second

pressure reducing valve must be connected in series.

Installation example (Fig. 4 )

1 Thermostat

2 Time switch

3 Circulation pump

4 Non-return valve

5 Outlet valve

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Tronic TR2000TF in the language / languages: English, German as an attachment in your email.

The manual is 1.92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch Tronic TR2000TF Manual

Product: