Manual Bosch TR1000 12 B (page 9 of 40) (English, German, Dutch, French)

697132

Zoom out

Zoom in

1/40

Installation instructions

TR1000 12 B – 6 720 876 017 (2019/06)

• Making use of the holes that were drilled for the old heater: Use the

mounting template to establish whether the existing holes line up

properly.

The following describes the installation procedure using the mounting

bolt.

Marking the point for mounting the heater and selecting the

opening for the connecting cable (Fig.A)

CAUTION:

Important!

Make sure that the connecting cable is isolated from the mains electricity

supply!

• Place hole 3 in the mounting template over the cold-water inlet.

• Select the most suitable hole through which the connecting cable is

be fed. The connecting cable must pass through one of the six holes

marked 14...

• Mark the point 12 at which the mounting bolt is to be inserted.

Fitting the mounting bolt and attaching the pipe connecting

pieces (Fig.B)

Open up the heater (Fig.C)

Punching out the holes at the rear of the heater for the mounting

bolt and the connecting cable

WARNING:

Important:

When mounting the appliance, only the holes actually required should be

punched out. Any other holes that are not going to be used must be

sealed watertight.

Inserting the connecting cable (Fig. D)

• Push the grommet 11 over the end of the connecting cable.

Note: Do not use the grommet for a cable with a cross-section

of 16 mm

. The appliance must then be installed flush with the wall.

WARNING:

Attention:

Without a grommet, the TR1000 12 B is splashproof only (IP 24).

• Place the heater over the connecting cable.

• Press the grommet into the hole in the rear wall of the heater through

which the cable should be fed. Ensure that the edges of the grommet

are flush with the hole all the way round.

• Fit the heater onto the threaded bushing 8 and secure it in place with

the nut 9.

Compensating for unevenness in the wall (Fig.E)

III. Water connection

• Using the locking screw 15, the water connection can be aligned

by ± 10 mm vertically.

• Adapt the bend in the “hot” pipe so that it lines up with the hot-water

outlet. In doing so, make sure that the “cold” elbow connection

is not bent.

CAUTION:

Attention:

Ensure that a distance of at least 6 mm is maintained to live parts

of the heater.

• Connect the water outlet and inlet and tighten the securing nut on

the mounting bolt.

Checking for leaks and flushing the heater:

• Turn on the hot-water tap.

• Check that all pipe joints are properly sealed.

IV. Electrical connection

• As a matter of principle, the water connections must be completed

first of all before the heater is connected to the electricity supply.

The appliance should be wired up according to the circuit diagram

on the inside of the cover.

• Circuit as delivered:

12 kW Y 400 V 3 ~ (11 kW Y 380 V 3 ~)

Connection Options:

– 8.0 kW 230 V ~ (7.4 kW 220 V ~)

– 6.0 kW 230 V ~ (5.5 kW 220 V ~)

(The required optional bridge can be found under accessories.)

• To guarantee compliance to relevant safety regulations, an all-pole

separator must be fitted during installation. The contact opening

must be at least 3 mm.

• The wires must not interfere with the operation of release button A on

the safety temperature limiter.

• Mark the selected output on the ratings plate.

Connection Options (Fig.A)

Definitiv wiring diagram in the appliance:

Installation note

• The installation of non plug-in ready appliances must be undertaken

by the respective utility operator or by a qualified specialist company,

who can also assist you when you are requesting the approval of

the utility company for installation of the appliance.

V. Mounting the cover onto the heater

VI. Startup

The device is compliant to IEC61000-3-12.

• Switch on via the heater fuses in the domestic wiring.

• Turn on the hot water tap and check the water temperature.

• Explain the appliance to the user and please give him the operating

instructions.

Priority switch for combination with electric storage heaters (Fig.A)

If the heater is going to be operated in this way, a priority switch must

be connected into the line connecting the L2 phase to the appliance.

It should be mounted on the meter or distribution panel.

f1 Safety temperature limiter with mains terminals 1-3-5.

l2 Change-over terminal strip

(The required optional bridge for the 6 kW230 V ~/5.5 kW

220 V ~ circuit can be found under accessories.)

a, b Control line for the electricity supply company connected

to the coil input on the charging contactor.

f1 Safety temperature limiter with mains terminals.

f3 Priority switch (current relay).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch TR1000 12 B in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch TR1000 12 B Manual

Product: