362550

Bosch tca 7301 vero professional 300 Manual

38
Zoom out
Zoom in
Previous page
1/132
Next page
34
deen
Dispensing hot water
! Risk of burns
The milk frother 10 gets very hot. After use,
allow to cool down first before touching.
The appliance must be ready for use.
Place the pre-warmed cup or glass under
the outlet of the milk frother 10.
Select the required setting for hot water
Ê
by turning the knob 6.
Press the
start
button 8. Hot water runs
out of the milk frother outlet 10 for about
40 seconds.
Press the
start
button 8 again to cut the
process short.
N.B.: It is possible to set the temperature of
the hot water (see “Controls, °
C
button”).
Maintenance and daily
cleaning
! Risk of electric shock
Unplug the appliance before cleaning it.
Never immerse the appliance in water.
Do not use a steam cleaner.
Wipe the outside of the appliance with a
soft, damp cloth. Do not use abrasive
cloths or cleaning agents.
Rinse the water tank 11 and the brewing
unit 23 with water only.
The cover of the storage compartment
25, the drip tray panel 26 and the cover of
the milk container 31 should only be
wiped gently with a damp cloth. Do not
put them in the dishwasher.
Remove cup stand 28. Pull the drip tray
27 with the coffee grounds container 29
forward and out, then empty and clean
them. All the parts can also be cleaned
in the dishwasher.
Clean the measuring spoon 14, the
aroma cover 16 and the milk container 31
by hand or in the dishwasher.
Wipe out the inside of the appliance (tray
holders).
●
●
●
●
●
●
●
●
●
●
Important:
The drip tray 27 should be
emptied and cleaned daily to prevent mould
from developing.
N.B.: If the appliance is cold when switched
on with the
a button 2, or if it is set to a
mode after brewing coffee, it rinses
automatically, in other words the system
cleans itself.
Cleaning the milk system
Clean the milk system 10 immediately after
use!
The milk system 10 can be pre-cleaned
automatically.
Select the
Ì
symbol in the display 5 and
press the
start
button 8.
PLACE EMPTY GLASS UNDER FROTHER,
P
LACE SUCTION PIPE IN GLASS
START
Place an empty glass under the milk
system 10 and put the end of the pipe
10d in the glass.
Press the
start
button 8. The appliance
now fills the glass automatically with
water and draws it in again through the
pipe 10d for cleaning. The rinse
procedure stops automatically after about
1 minute.
Now empty the glass and clean the pipe
10d.
In addition to this, clean the milk system
thoroughly at regular intervals (by hand or
in the dishwasher).
Dismantling the milk system 10 for
cleaning:
Pull the milk system 10 forward out of the
appliance.
Clean the individual parts (Fig. C) with a
detergent solution and a soft brush.
Rinse all parts with clear water and dry
them.
Reassemble all the parts and replace fully
in the appliance.
Note: All the parts of the milk frother 10 can
also be put in the dishwasher.
●
●
●
●
●
●
●
●
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch tca 7301 vero professional 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch tca 7301 vero professional 300 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info