78191
6
Zoom out
Zoom in
Previous page
1/10
Next page
Place the machine on the edge of the lawn, as
close to the power point as possible. Work away
from the power point. Then at right angles.
Position the cable to opposite side (already cut) at
the end of each turn.
When mowing
do not allow the motor to la-
bour
particularly in heavy conditions. When
the motor labours the speed of the motor
drops and you will hear a change in the motor sound,
when this occurs stop mowing, release the switch le-
ver and
raise the height of cut
. Failure to do so
could damage the machine.
NOTE:
The motor is protected by a safety cut out
which is activated when the blade becomes jammed
or if the motor is overloaded.
When this occurs
stop, remove the plug from the power supply.
The safety cut out will only reset when the switch
lever 1 is released. Clear any obstruction and
wait for a few minutes for the safety cut out to re-
set before continuing to use the mower. At this
time do not operate the switch lever 1 as this will
prolong the reset time of the safety cut out. If the
mower cuts out again increase the height of cut
to reduce the load on the motor.
Stop, remove plug from the power supply
and remove the grassbox.
Note: To ensure long and reliable service, carry out
the following maintenance regularly.
Regularly check for obvious defects such as loose,
dislodged or damaged blade, loose fixings, and
worn or damaged components.
Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or
repairs before using.
If the machine should happen to fail despite the care
taken in manufacture and testing, repair should be
carried out by an authorised customer service agent
for Bosch garden products.
For all correspondence and spare parts orders, al-
ways include the 10-digit part number (TYP) from
the nameplate of the machine!
Stop, remove plug from the power supply
and remove the grassbox.
Turn the machine on its right side and inspect the
blade and fan; if blunt or damaged, replace.
Use the following procedure to remove and replace
the blade. Hold the blade
16
using gardening gloves
(not provided) use a spanner (not provided) to re-
move the blade bolt
15
, blade washer
17
, bevel
washer
18
and blade. Fit the bevel washer, blade,
blade washer and the blade bolt. Ensure that the
blade is the correct way up (so that this symbol
can be seen located as in figure
G
) and tighten the
bolt firmly.
In the event of a blade becoming difficult to remove
or fit, insert a screwdriver into hole
19
to lock the
drive. Ensure the screwdriver is removed before at-
tempting to turn the machine on.
Clean the exterior of the machine thoroughly using a
soft brush and cloth. Do not use water, solvents or
polishes. Remove all grass and debris, especially
from the ventilation slots
11
.
Turn the machine on its side and clean the blade
area. If grass cuttings are compacted in the blade
area, remove with a wooden or plastic implement.
Store the machine in a dry place. Do not place other
objects on top of the machine.
To aid storage loosen the wing nuts
13
and fold the
handles.
Ensure cables are not trapped when folding/
unfolding top handles,
do not drop the han-
dles
.
Mowing
Maintenance
F
Blade Maintenance
After Mowing/Storage
G
F016 L70 483 06.10
F016 L70 321 - GB Seite 4 Montag, 30. Oktober 2006 3:56 15
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch ROTAK 320 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch ROTAK 320 in the language / languages: English as an attachment in your email.

The manual is 1,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch ROTAK 320

Bosch ROTAK 320 User Manual - English, German - 195 pages

Bosch ROTAK 320 User Manual - Dutch - 170 pages

Bosch ROTAK 320 User Manual - Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 195 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info