780635
30
Zoom out
Zoom in
Previous page
1/56
Next page
Infos/Alarme
Rego 5200 – 6721824506 (2020/09)
30
6.6 Alarmfunktionen
A- und B-Alarme müssen nach der Behebung stets entriegelt werden,
damit die Wärmepumpe neu startet. C-Alarme werden automatisch ent-
riegelt.
Bei A- und B-Alarmen schnellstmöglich an den Kundendienst wenden.
Bei wiederholtem Auftreten von C-Alarmen an den Kundendienst
wenden.
6.6.1 A-Alarme
Tab. 56 Infos/Alarme
6.6.2 B-Alarme
Alarm-/Infotext Wärme-
pumpe
Stopp
Kompr. 1
Stopp
Kompr. 2
Stopp Zu-
heizer
Stopp
WW
Cat. Ursache/Anmerkung
Betriebsfehler alle PC1 Z1 X X X A Sofort beheben! Gefahr von Frostschäden.
Funktion aller Pumpen prüfen.
▶Anschlüsse prüfen.
Betriebsfehler Kompr. u.
Zus.heiz.
Z1 X X X X A Sofort beheben! Gefahr von Frostschäden.
Kontrollieren, welche weiteren (B-)Alarme vor-
liegen und diese beheben.
Zuheizer und Überhitzungsschutz/Thermostat
kontrollieren.
Störung an Fühler T0 und TC21) Z1 X X A Sofort beheben! Gefahr von Frostschäden.
Fühleranbringung prüfen.
Anschluss prüfen, Widerstand messen und mit
Widerstandstabelle vergleichen.
Bei Bedarf Fühler tauschen.
Fehler Sensor TW1 X A, B Fehler am Vorlauftemperaturfühler in der Frisch-
wasserstation (FWS). PC4 wird gestoppt.
Fühleranbringung überprüfen.
Anschluss prüfen, Widerstand messen und mit
der Widerstandstabelle vergleichen.
Bei Bedarf Fühler tauschen.
Störung PC4 – Heizwasserpumpe
x A Alarm von der Zirkulationspumpe in der Frischwas-
serstation.
Leitungen zwischen Frischwasserstation und
Pufferspeicher entlüften.
Wenn die Zirkulationspumpe überhitzt, sicher-
stellen, dass Hähne/Ventile geöffnet sind.
1) Je nach System
Alarm-/Infotext Wärme-
pumpe
Stopp
Kompr. 1
Stopp
Kompr. 2
Stopp
Kompr. 3
Stopp
WW
Cat. Ursache/Anmerkung
Fehler Sensor TW1 TW1 X B Ggf. startet der Notbetrieb: ( "Warmwasser-Not-
betrieb"). Für die Temperatur wird im Display NaN
angezeigt.
Überprüfen, ob die Warmwasserart in der
Bedieneinheit richtig eingestellt wurde.
Fühleranbringung überprüfen.
Anschluss prüfen, Widerstand messen und mit
der Widerstandstabelle vergleichen.
Bei Bedarf Fühler tauschen.
Fehler Sensor TC0, TB0, TB1 Alle (X) (X) B Bei einer Störung an TC0 werden beide Kompresso-
ren abgeschaltet. Bei Störungen an TB0 gilt für die
Regelung TB1 + Sollwert PB3-Delta. Bei Störungen
an TB1 gilt für die Regelung TB0 - Sollwert PB3-Del-
ta. Als Temperatur wird im Display NaN angezeigt.
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Rego 5200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Rego 5200 in the language / languages: German as an attachment in your email.

The manual is 6.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch Rego 5200

Bosch Rego 5200 User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info