780636
9
Zoom out
Zoom in
Previous page
1/24
Next page
Settings Customer level
Rego 1000 – 6 721 831 662 (2021/03) en 9
For description of setting of Extra hot water
(Chapter 6.3, 2.3 Extra hot water ).
Party
Party mode means that a running room program is stopped during the
set time in order to avoid a temperature drop.
>Number of hours
Select the number of hours that party mode should be active for.
The function starts immediately on all activated circuits.
>Circuit x
Select Yes to enable party mode.
Party mode can be enabled for each installed circuit. The menu is
displayed only if more than one circuit is installed.
>Deactivate party mode
Select Yes to disable party mode on all activated circuits.
The heat pump returns to program mode.
The menu is displayed only if party mode is active.
Holiday
For description of setting of Holiday
(Chapter 6.3, 3 Holiday ).
Disable cooling
The menu is displayed only if the cooling function is installed and affects
all circuits with cooling.
6.2 Room temperature
Press the button in the Initial menu to move to the top menu level.
Select 1 Room temperature to adjust the heating.
Under 1 Room temperature there is:
1.1 Circuit 1 Heating
1.3/1.4 Circuit 2, 3... (option)
1.10 General
1.1 Circuit 1 Heating
1.1.5 Heat curve
The heat curve constitutes the basis for the control unit's control of the
temperature on the heating water to the circuit and indicates how high it
needs to be in relation to the outdoor temperature. The control unit
increases the temperature of the heating water when the outdoor
temperature drops. The temperature of the heating water out to the
circuit, i.e. the flow temperature is measured by sensor T1 for circuit 1
(full name E11.T1) and sensor T1 for circuit 2 (full name E12.T1).
Each circuit is controlled by its own heat curve. The installer sets the
type of heating for each circuit, that is Radiator or Underfloor. The heat
curve for Underfloor has lower values because the floors do not tolerate
such high temperatures.
Fig. 17 Radiator
The figure indicates the factory setting curve for a radiator circuit. At -
2.5 °C the flow set point is 37.4 °C.
Fig. 18 Underfloor
The figure indicates the factory setting curve for an underfloor circuit. At
-2.5 °C the flow set point is 27.2 °C.
Setting of heat curve
A heat curve is set for each circuit. If the room temperature is perceived
to be too high or too low in the circuit, it is preferable to adjust the curve.
The curve can be changed in different ways. The slope of the curve can
be changed by offsetting the flow temperature upwards or downwards
on the left-hand side (the value at outdoor temperature 20 °C, factory
value 22.0 °C) as well as the right-hand side (the value at outdoor
After a period with blocked hot water production, e.g.,
holiday, it is recommended to enable the extra hot water
function so as to eliminate bacteria and quickly reach the
correct hot water temperature.
Factory setting 0h
Lowest value 0h
Highest value 99h
Table 4 Party duration
Factory setting No
Alternative No/Yes
Table 5 Enable party mode
Factory setting No
Alternative No/Yes
Table 6 Deactivate party mode
It takes a long time before the cooling mode manages to
affect the temperature in the house, therefore wait at
least one day after disabling/enabling before making any
additional adjustments.
If the heat curve has been set too high, the display will
show the message Too high heat curve setting.
Change the heat curve setting.
6 720 614 789-15.3I
1(˚C)
T2(˚C)
20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35
80
70
60
50
40
30
20
10
6 720 614 789-16.3I
T
1(˚C)
T2(˚C)
20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35
80
70
60
50
40
30
20
10
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Rego 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Rego 1000 in the language / languages: English as an attachment in your email.

The manual is 4.13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info