544276

Bosch RC 1 Manual

26
Zoom out
Zoom in
Previous page
1/351
Next page
26 | English
1 609 92A 0D9 | (24.3.14) Bosch Power Tools
– After levelling, direct the laser beam in point operation on-
to the close wall A. Mark the centre point of the laser beam
on the wall (point I).
– Turn the measuring tool around by 180°, allow it to level in
and mark the centre point of the laser beam on the oppo-
site wall B (point II).
– Without turning the measuring tool, position it close to wall
B. Switch the measuring tool on and allow it to level in.
– Align the height of the measuring tool (using the tripod or
by underlaying, if required) in such a manner that the cen-
tre point of the laser beam is projected exactly against the
previously marked point II on wall B.
– Rotate the measuring tool by 180° without changing the
height. Allow it to level in and mark the centre point of the
laser beam on wall A (point III). Take care that point III is
as vertical as possible above or below point I.
The difference d of both marked points I and III on wall A
amounts to the actual deviation of the measuring tool for the
measured axis.
– Repeat the measuring procedure for the other three axes.
For this, turn the measuring tool prior to each measuring
procedure by 90°.
The maximum permitted deviation over the measuring sec-
tion of 2 x 20 m = 40 m is as follows:
40mx±0.1mm/m=±4mm.
The difference d between points I and III must therefore be
maximum 8 mm in each of the four measuring procedures.
If the measuring tool should exceed the maximum deviation in
any one of the four measuring procedures, have it checked at
a Bosch after-sales service agent.
Working Advice
Always use the centre of the laser point for marking.
The size of the laser point changes with the distance.
Laser Viewing Glasses (Accessory)
The laser viewing glasses filter out ambient light. This enhanc-
es the laser visibility for the eye.
Do not use the laser viewing glasses as safety goggles.
The laser viewing glasses are used for improved visualisa-
tion of the laser beam, but they do not protect against laser
radiation.
Do not use the laser viewing glasses as sun glasses or in
traffic. The laser viewing glasses do not afford complete
UV protection and reduce colour perception.
Working with the Laser Receiver (Accessory)
Under unfavourable light conditions (bright environment, di-
rect sunlight) and for larger distances, use the laser receiver
for improved finding of the laser beam 35.
When working with the laser receiver, select rotational opera-
tion with the highest rotational speed.
Before working with the laser receiver, read and observe the
laser receiver operating instructions.
Working with the Remote Control
While pressing the operator buttons, the measuring tool can
be brought out of alignment so that the rotation is briefly
stopped. This effect is avoided when using the remote con-
trol.
Reception lenses 7 for the remote control are located on three
sides of the measuring tool, among other locations above the
control panel on the front side.
Working with the Tripod (Accessory)
– The measuring tool is equipped with a 5/8" tripod mount
for horizontal operation on a tripod. Place the measuring
tool via the tripod mount 18 onto the 5/8" male thread of
the tripod and screw the locking screw of the tripod tight.
On a tripod 37 with a measuring scale on the elevator column,
the height difference can be adjusted directly.
AB
20 m
AB
180°
AB
AB
180°
OBJ_BUCH-757-008.book Page 26 Monday, March 24, 2014 11:19 AM
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch RC 1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch RC 1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 22,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info