656957
39
Zoom out
Zoom in
Previous page
1/44
Next page
Trouble shooting en
39
3Trouble shooting
Trouble shooting
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Cleaning
How do I clean the hob?
Using a special glass-ceramic cleaning agent produces the best results. We advise against using harsh or abrasive cleaning agents, dish-
water detergent (concentrated) or scouring pads.
You can find more information on cleaning and caring for your hob in the section on ~ "Cleaning"
Indicator Possible cause Remedial action
None The power supply has been disconnected. Use other electrical devices to check whether a short-circuit has
occurred in the power supply.
The device has not been connected as shown in
the circuit diagram.
Check that the device has been connected as shown in the circuit
diagram.
Fault in the electronics. If the fault cannot be rectified, inform the technical after-sales ser-
vice.
The indicators are flashing The control panel is damp or an object is cover-
ing it.
Dry the control panel or remove the object.
The Ù indicator is flashing in
the hotplate displays
A fault has occurred in the electronics. To acknowledge the fault, briefly cover the control panel with
your hand.
”ƒ / “‰ƒ‹ˆ
The electronics have overheated and switched
off the relevant hotplate.
Wait until the electronics have cooled down sufficiently. Then
touch any symbol on the hob.
”… / “‰ƒ‹‰
The electronics have overheated and all the hot-
plates have been switched off.
Ӡ + heat setting and signal
There is a hot saucepan in the control panel
area. There is a risk that the electronics will over-
heat.
Remove the saucepan. The fault indicator will go out shortly after-
wards. You can continue cooking.
Ӡ and signal
There is a hot saucepan in the control panel
area. The hotplate has been switched off to pro-
tect the electronics.
Remove the saucepan. Wait a few seconds. Touch any control.
You can continue cooking once the fault indicator has gone out.
”‚ / ”‡
The hotplate has overheated and been switched
off to protect the work surface.
Wait until the electronics have cooled down sufficiently before
switching the hotplate on again.
”‹
You cannot activate the transfer settings function Check the fault indicator by touching any control. You can cook
as usual without using the transfer settings function. Contact the
technical after-sales service.
”Š
You cannot activate the FlexPlus cooking zone Check the fault indicator by touching any control. You can use the
remaining hotplates to cook as usual. Contact the technical after-
sales service.
”‰
The hotplate has been operating continuously for
an extended period.
The automatic safety switch-off function has been activated. See
the section on ~ "Automatic safety cut-out"
“‰ƒ‹ƒ
The temperature sensor has overheated and the
hotplate has been switched off.
Wait until the temperature sensor has cooled down sufficiently
before activating the function again.
“‰ƒ‹„
The temperature sensor has overheated and all
the hotplates have been switched off.
If you are not using the temperature sensor, remove it from the
cookware and store it far away from the other hotplates and
sources of heat. Switch the hotplate back on.
“‰ƒ‹…
The battery in the temperature sensor is flat. Change the 3V CR2032 battery. See the section on
~ "Changing the battery"
“‰ƒ‹†
The temperature sensor is disconnected. Switch the function off and on again.
“‰ƒ‹‡
The temperature sensor is broken/faulty. Contact the technical after-sales service.
Do not place hot pans on the control panel.
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PXY895DE3E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PXY895DE3E in the language / languages: English as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PXY895DE3E

Bosch PXY895DE3E User Manual - German - 48 pages

Bosch PXY895DE3E User Manual - Dutch - 88 pages

Bosch PXY895DE3E User Manual - French - 48 pages

Bosch PXY895DE3E User Manual - Italian - 88 pages

Bosch PXY895DE3E Installation Guide - All languages - 22 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info