746102
40
Zoom out
Zoom in
Previous page
1/44
Next page
en Trouble shooting
40
3Trouble shooting
Tr oubl e s hoot i ng
Usually, faults are small matters that are easy to
eliminate. Please read the information in the table
before calling the after-sales service.
Notes
If appears on the display, press and hold the
button for the relevant cooking zone in order to read
the fault code.
If the fault code is not listed in the table, disconnect
the hob from the mains power supply and wait
30 seconds before reconnecting it. If this code is
displayed again, contact the technical after-sales
service and specify which fault code has appeared.
If a fault occurs, the appliance will not switch to
standby mode.
Indicator/symbol Possible cause Solution
None The power supply has been disconnected. Use other electrical appliances to check whether a short circuit
has occurred in the power supply.
The appliance has not been connected as shown
in the circuit diagram.
Make sure that the appliance has been connected as shown in
the circuit diagram.
Electronics fault. If the fault cannot be rectified, inform the technical after-sales ser-
vice.
The indicators are flashing The control panel is damp or there is something
on it.
Dry the control panel or remove the object.
Ù is flashing on the cooking
zone displays
A fault has occurred in the electronics. To acknowledge the fault, briefly cover the control panel with
your hand.
”ƒ / “ˆ‹‚† The electronics have overheated and have
switched off the affected cooking zone.
Wait until the electronics have cooled down sufficiently. Then
touch any symbol on the hob.
”… / “ˆ‹‚† The electronics have overheated and all the
cooking zones have been switched off.
Ӡ + heat setting and signal
tone
There is hot cookware near the control panel.
There is a risk that the electronics will overheat.
Remove the cookware that is causing the problem.The fault code
will go out shortly afterwards. You can now resume cooking.
Ӡ and signal tone There is hot cookware near the control panel. To
protect the electronics, the cooking zone has
been switched off.
Remove the cookware that is causing the problem. Wait a few
seconds. Touch any touch control. When the fault code on the dis-
play goes out, you can resume cooking.
”‚ / ”‡ The cooking zone has overheated and has been
switched off to protect the work surface.
Wait until the electronics have cooled down sufficiently before
switching the cooking zone back on.
”‰ The cooking zone has been operating continu-
ously for an extended period.
The automatic safety shut-off function has been activated. See
the section entitled
“ˆ‹‚‹ The hob is unable to connect to your home net-
work or the extractor hood.
Acknowledge the fault code by touching any of the buttons. You
can cook as usual without a connection.
If this code is displayed again, contact the technical after-sales
service.
“Š‹‹‹
“Š‹‚‹
The operating voltage is incorrect/outside of the
normal operating range.
Contact your electricity supplier.
—…‹‹ The hob is not connected properly Disconnect the hob from the mains power supply. Make sure that
it has been connected as shown in the circuit diagram.
š“ Demo mode is active Disconnect the hob from the mains power supply. Wait for
30 seconds before reconnecting it. Touch any button within the
next 3 minutes. Demo mode is now deactivated.
Do not place hot cookware on the control panel.
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PXV890DV5E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PXV890DV5E in the language / languages: English as an attachment in your email.

The manual is 3,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PXV890DV5E

Bosch PXV890DV5E User Manual - German - 44 pages

Bosch PXV890DV5E User Manual - Dutch - 44 pages

Bosch PXV890DV5E User Manual - French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info