Manual Bosch PWS 720-115 (page 28 of 167) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

79294

Zoom out

Zoom in

1/167

28 | English

1 609 929 R16 | (28.9.09) Bosch Power Tools

To switch off the power tool, release the On/Off

switch 3 or, if it is locked, briefly push down the

back of the On/Off switch 3 and then release it.

f Check grinding tools before using. The

grinding tool must be mounted properly

and be able to move freely. Carry out a test

run for at least one minute with no load. Do

not use damaged, out-of-centre or vibrating

grinding tools. Damaged grinding tools can

burst and cause injuries.

Working Advice

f Exercise caution when cutting slots in

structural walls; see Section “Information

on Structures ”.

f Clamp the workpiece if it does not remain

stationary due to its own weight.

f Do not strain the machine so heavily that it

comes to a standstill.

f After heavily straining the power tool, con-

tinue to run it at no-load for several minutes

to cool down the cutting/grinding tool.

f Grinding and cutting discs become very hot

while working; do not touch until they have

cooled.

f Do not use the power tool with a cut-off

stand.

Rough Grinding

f Never use a cutting disc for roughing.

The best roughing results are achieved when

setting the machine at an angle of 30° to 40°.

Move the machine back and forth with moderate

pressure. In this manner, the workpiece will not

become too hot, does not discolour and no

grooves are formed.

Flap Disc

With the flap disc (accessory), curved surfaces

and profiles can be worked.

Flap discs have a considerably higher service

life, lower noise levels and lower sanding tem-

peratures than conventional sanding sheets.

Cutting Metal

f For cutting metal, always work with the pro-

tection guard for cutting 7.

When cutting, work with moderate feed, adapt-

ed to the material being cut. Do not exert pres-

sure onto the cutting disc, tilt or oscillate the

machine.

Do not reduce the speed of running down cut-

ting discs by applying sideward pressure.

The machine must

always work in an

up-grinding mo-

tion. Otherwise,

the danger exists

of it being pushed

uncontrolled out

of the cut.

When cutting pro-

files and square

bar, it is best to

start at the small-

est cross section.

Cutting Stone

f For cutting stone, always work with the cut-

ting guide with dust extraction protection

guard 16.

f The machine may be used only for dry cut-

ting/grinding.

For cutting stone, it is best to use a diamond

cutting disc. As a safety measure against jam-

ming, the cutting guide with dust extraction pro-

tection guard 16 must be used.

Operate the machine only with dust extraction

and additionally wear a dust protection mask.

The vacuum cleaner must be approved for the

extraction of masonry dust. Bosch provides suit-

able vacuum cleaners.

Switch on the ma-

chine and place

the front part of

the cutting guide

on the workpiece.

Slide the machine

with moderate

feed, adapted to

the material to be

worked.

OBJ_BUCH-393-004.book Page 28 Monday, September 28, 2009 2:16 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PWS 720-115 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PWS 720-115

Bosch PWS 720-115 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 166 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PWS 720-115 Manual

Product: