119895

Bosch PWS 7-100 Manual

17
Zoom out
Zoom in
Previous page
1/115
Next page
English - 6
(for M 14 grinder spindle)
Instead of the clamping nut 10, the quick-clamp-
ing nut 11 (accessory) can be used. Grinding
tools can then be mounted without using tools.
The quick-clamping nut 11 may be used only
for grinding and cutting discs.
Use only a flawless, undamaged quick-clamp-
ing nut 11.
When screwing on, take care that the side
with printing does not point to the grinding
disc. The arrow must point to the index
mark 20.
Lock the grinder
spindle with the spin-
dle lock button 3.
Tighten the quick-
clamping nut by
forcefully turning the
grinding disc in the
clockwise direction.
A properly tightened
undamaged, quick-
clamping nut can be
loosened by hand
turning the knurled
ring by hand in an an-
ticlockwise direction.
Never loosen a tight
quick-clamping nut
with pliers but use a
two-pin spanner. In-
sert the two-pin
spanner as shown in
the illustration.
All grinding tools mentioned in these operating in-
structions can be used.
The permissible speed [rpm] or the circumferen-
tial speed [m/s] of the grinding tools used must at
least match the values given in the table.
Therefore, always observe the permissible
rotational/circumferential speed on the label
of the grinding tool.
Observe correct mains voltage: The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
To start the machine, press the On/Off switch 1
forward.
To lock-on, press the On/Off switch 1 down at
the front until it engages.
To switch off the machine, release the On/Off
switch 1 or, when the switch is locked, briefly
press down the On/Off switch 1 at the rear.
☞
Test run!
Check the grinding tool before use. The
grinding tool must be properly mounted
and rotate freely. Perform a test run of at
least 30 seconds without load. Do not use
damaged, out-of-round or vibrating grind-
ing tools.
Constant Electronic Control
(PWS 8-125 CE/PWS 9-125 CE)
Constant electronic control holds the speed con-
stant at no-load and under load, and ensures uni-
form working performance.
Overload Protection
(PWS 8-125 CE/PWS 9-125 CE)
When overloaded, the motor comes to a stop.
Relieve the load on the machine immediately and
allow to cool for approx. 30 seconds at the high-
est no-load speed.
Quick Clamping Nut
Approved Grinding Tools
3
20
11
3
max.
[mm] [mm]
Db d[rpm] [m/s]
100
115
125
6
6
6
16.0
22.2
22.2
11 000
11 000
11 000
80
80
80
100
115
125
–
–
–
–
–
–
11 000
11 000
11 000
80
80
80
70
75
30
30
M 10
M 14
11 000
11 000
45
45
Starting Operation
b
d
D
D
D
b
d
2 609 000 850.book Seite 6 Montag, 23. Januar 2006 9:16 09
17 • 2 609 000 850 • 06.01
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PWS 7-100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PWS 7-100 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info