Manual Bosch PWS 7-100 (page 14 of 115) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

119895

Zoom out

Zoom in

1/115

English - 3

■ Always direct the cable to the rear away from

the machine.

■ Always switch the machine off and wait until it

has come to a standstill before placing it down.

■ For power outage or when the mains plug is

pulled, unlock the On/Off switch immediately

and turn it to the Off position. This prevents un-

controlled restarting.

■ The machine must be used only for dry cutting/

grinding.

■ For all work with the machine, the auxiliary

handle must be mounted.

■ When performing an operation where the

tool insert can run into concealed electric

lines, hold the machine by the insulated

handles only.

Contact with a “live” wire will make exposed

metal parts of the tool “live” and shock the op-

erator.

■ Use suitable detectors to determine if util-

ity lines are hidden in the work area or call

the local utility company for assistance.

Contact with electric lines can lead to fire and

electric shock. Damaging a gas line can lead

to explosion. Penetrating a water line causes

property damage or may cause an electric

shock.

■ For work with grinding or cutting discs, the pro-

tection guard 6 must be mounted. For work

with the rubber sanding plate 13 or with the

cup brush 16/disc brush/flap disc, the hand

guard 12 (accessory) is to be mounted.

■ Use dust extraction when working with stone.

The vacuum cleaner must be approved for ma-

sonry dust. When cutting stone, use the cutting

guide.

■ Do not work with materials containing asbes-

tos.

■ Use only grinding tools with a permissible

speed at least as high as the no-load speed of

the machine.

■ Check grinding tools before use. The grinding

tool must be properly mounted and turn freely.

Perform a test run for at least 30 seconds with-

out load. Do not use damaged, out-of-round or

vibrating grinding tools.

■ Protect the grinding tool from impact, shock

and grease.

■ Apply the machine to the workpiece only when

switched on.

■ Keep hands away from rotating grinding tools.

■ Pay attention to the direction of rotation. Al-

ways hold the machine so that sparks and

grinding dust fly away from the body.

■ When grinding metal, flying sparks are pro-

duced. Take care that no persons are endan-

gered. Due to danger of fire, no combustible

materials should be located in the vicinity

(spark flight zone).

■ Be careful when cutting grooves, e. g. in struc-

tural walls: See Information on Structures.

■ Blocking the cutting disc leads to jerking reac-

tion forces on the machine. In this case switch

off the machine immediately.

■ Observe the dimensions of the grinding discs.

The hole diameter must fit mounting

flange 8 (M 14), 19 (M 10). Do not use any re-

ducers or adapters.

■ Never use cutting discs for rough grinding. Do

not exert any lateral pressure on the cutting

discs.

■ Observe the manufacturer’s instructions for

mounting and using grinding tools.

■ Caution! The grinding tool runs on after the

machine is switched off.

■ Do not clamp the machine in a vice.

■ Never allow children to use the machine.

■ Bosch is only able to ensure perfect operation

of the machine if the original accessories in-

tended for it are used.

Slots in structural walls are subject to the Stand-

ard DIN 1053, Part 1 or country-specific regula-

tions.

These regulations are to be observed under all

circumstances. Before beginning work, consult

the responsible structural engineer, architect or

the construction supervisor.

Information on Structures

2 609 000 850.book Seite 3 Montag, 23. Januar 2006 9:16 09

14 • 2 609 000 850 • 06.01

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PWS 7-100 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PWS 7-100 Manual

Product: