390515
13
Zoom out
Zoom in
Previous page
1/115
Next page
English - 2
The machine is intended for cutting, roughing and
brushing metal and stone materials without using
water. For cutting stone, a cutting guide is re-
quired.
For machines with electronic control: With ap-
proved sanding tools, the machine can be used
for sanding and polishing.
Measured values determined according to
EN 50 144.
Typically the A-weighted noise levels of the ma-
chine are: Sound pressure level: 88 dB (A);
sound power level: 101 dB (A).
Wear hearing protection!
When using the standard auxiliary handle, the
typically weighted maximum acceleration is
5.3 m/s
2
.
When using the vibration-dampening auxiliary
handle, the typically weighted maximum acceler-
ation is 5.3 m/s
2
. The hand-arm vibration at the
auxiliary handle is typically lower than 2.5 m/s
2
.
The numbering of the machine elements refers to
the illustration of the machine on the graphics
page.
While reading the operating instructions, unfold
the graphics page for the machine and leave it
open.
1 On/Off switch
2 Thumbwheel for speed preselection
(PWS 8-125 CE/PWS 9-125 CE)
3 Spindle lock button
4 Auxiliary handle
5 Grinder spindle
6 Protection guard
7 Clamping lever
8 Mounting flange
(for the M 14 grinding spindle with O-ring)
9 Grinding-/cutting disc*
10 Clamping nut
11 quick-clamping nut*
12 Hand guard*
13 Rubber sanding plate*
14 Sanding sheet*
15 Round nut*
16 Cup brush*
17 Cutting guide with dust extraction protection
guard*
18 Diamond cutting disc*
19 Mounting flange M 10
* Not all of the accessories illustrated or described are
included as standard delivery.
Working safely with this ma-
chine is possible only when the
operating and safety information
are read completely and the in-
structions contained therein are
strictly followed. Additionally,
the general safety instructions either in the
enclosed booklet or those added in the centre
of these operating instructions must be ob-
served. Before using for the first time, ask for
a practical demonstration.
Wear hearing protection.
Wear safety goggles.
Wear additional protection equipment for your
safety, such as protective gloves, sturdy
shoes, hard hat and apron.
The dust that is produced while working can be
detrimental to health, inflammable or explo-
sive. Suitable safety measures are required.
Examples: Some dusts are regarded as carci-
nogenic. Use suitable dust/chip extraction and
wear a dust protection mask.
Dust from light alloys can burn or explode. Al-
ways keep the workplace clean, as blends of
materials are particularly dangerous.
If the mains cable is damaged or cut through
while working, do not touch the cable but im-
mediately pull the mains plug. Never use the
machine with a damaged cable.
Connect machines that are used in the open
via a residual current device (RCD) with an ac-
tuating current of 30 mA maximum. Do not op-
erate the machine in rain or moisture.
When working with the machine, always hold it
firmly with both hands and provide for a secure
stance.
Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
securely than by hand.
Intended Use
Noise/Vibration Information
Machine Elements
For Your Safety
2 609 000 850.book Seite 2 Montag, 23. Januar 2006 9:16 09
13 • 2 609 000 850 • 06.01
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch pws 6 115 e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch pws 6 115 e in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info