Manual Bosch PWS 1900 (page 13 of 111) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

79059

Zoom out

Zoom in

1/111

English - 3

■ When grinding metal, flying sparks are pro-

duced. Take care that no persons are endan-

gered. Due to danger of fire, no combustible

materials should be located in the vicinity

(spark flight zone).

■ Be careful when cutting grooves, e. g. in struc-

tural walls: See Information on Structures.

■ Blocking the cutting disc leads to jerking reac-

tion forces on the machine. In this case switch

off the machine immediately.

■ Pay attention to the dimensions of the grinding

disc. The mounting hole diameter must fit the

mounting flange 9 without play. Do not use re-

ducers or adapters.

■ Never use cutting discs for rough grinding. Do

not exert any lateral pressure on the cutting

discs.

■ Observe the manufacturer’s instructions for

mounting and using grinding tools.

■ Caution! The grinding tool runs on after the

machine is switched off.

■ Do not clamp the machine in a vice.

■ Never allow children to use the machine.

■ Bosch is only able to ensure perfect operation

of the machine if the original accessories in-

tended for it are used.

Slots in structural walls are subject to the Stand-

ard DIN 1053, Part 1 or country-specific regula-

tions.

These regulations are to be observed under all

circumstances. Before beginning work, consult

the responsible structural engineer, architects or

the construction supervisor.

■ Before any work on the machine itself, pull

the mains plug.

■ For work with grinding or cutting discs, the

protection guard 6 must be mounted.

Protection Guard with Locking Screw

The coded projection 8 on the protection guard 6

ensures that only a guard that fits the machine

type can be mounted.

Loosen the clamping screw 7, if necessary.

Place the protection guard 6 with coded projec-

tion 8 into the coded groove on the spindle collar

of the machine head and rotate to the required

position (working position).

The closed side of the protection guard 6

must always point to the operator.

Tighten clamping screw 7.

Protection Guard with Quick Clamp

☞

The protection guard is preadjusted to the

diameter of the spindle collar. If required,

the tightening tension of the clamping

bracket can be changed by tightening or

loosening the adjustment screw 13. Al-

ways ensure that the protection guard 6 is

seated tightly on the spindle collar.

Open the clamping lever 14.

Place the protection guard 6 with coded projec-

tion 8 into the coded groove on the spindle collar

of the machine head and rotate to the required

position (working position).

To fasten the protection guard 6, close the

clamping lever 14.

The closed side of the protection guard 6

must always point to the operator.

Auxiliary Handle

■ For all work with the machine, the auxiliary

handle must be mounted.

Screw the auxiliary handle 4 into the head of the

machine according to the working method.

Vibration-dampening Auxiliary Handle

The vibration-dampening auxiliary handle re-

duces the vibrations, making operation more

comfortable and secure.

Do not make any alterations to the aux-

iliary handle.

Do not continue to use an auxiliary handle if it is

damaged.

Hand Guard

For work with the rubber sanding plate 20 or with

the cup brush 23/disc brush/flap disc, the hand

guard 18 (accessory) is to be mounted. The hand

guard 18 is fastened with the auxiliary handle 4.

Information on Structures

Mounting the

Protective Devices

1 609 929 R44 - Buch Seite 3 Dienstag, 11. März 2008 2:06 14

13 • 1 609 929 R44 • 05.01

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PWS 1900 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PWS 1900

Bosch PWS 1900 User Manual - Dutch - 111 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PWS 1900 Manual

Product: