Manual Bosch PTA 2400 (page 14 of 91) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544042

Zoom out

Zoom in

1/91

14 | English

1 609 929 T64 | (17.6.11) Bosch Power Tools

Mounting the Length Stop and Workpiece Support

(see figures B1–B2)

– Screw the length stop 6 to the workpiece support 8 with

carriage bolt M6 x 46 and locking knob 7.

– Insert the workpiece support 8 into the table extension 10.

– Tighten the locking knob 9 to lock the workpiece support.

– Repeat the worksteps with the second workpiece support.

Preparing the Saw Stand

Preparing the Attachment Sets (see figures C1–C3)

– Place both attachment sets 1 on the saw stand in such a

manner that the labelling can be read.

– Hand-tighten both locking knobs 5.

– Place the retaining adapters 2 with the flat side facing

upward on both attachment sets and move them apart so

that the fastening holes 15 are aligned.

– Guide two assembly-sliding plates 16 each (perpendicu-

lar, with the flat side facing upward) from the rear into the

guide compartment of the attachment sets 1.

Move the assembly-sliding plates apart so that they are

aligned with the fastening holes 15.

– Hand-tighten the attachment sets and retaining adapters

with the washers and hexagon bolts from fastening kit 12.

– Afterwards, firmly tighten both locking knobs 5 of the at-

tachment sets.

Fastening the Power Tool to the Attachment Sets

(see figures D1–D3)

– Position the power tool in the transport position. Notes on

the transport position are given in the operating instruc-

tions of the respective power tool.

– Position the power tool on the front retaining adapter in

such a manner that the front mounting holes on the power

tool are brought into alignment with the slots of the retain-

ing adapter.

– Screw the front retaining adapter and the power tool to-

gether with the hexagon bolts, washers and wing nuts from

the fastening kit 13.

– Position the rear retaining adapter in such a manner that

the rear mounting holes on the power tool are brought into

alignment with the slots of the retaining adapter.

– Screw the rear retaining adapter and the power tool to-

gether with the hexagon bolts, washers and wing nuts from

the fastening kit 13.

– Align the retaining adapters 2 uniformly.

The imprinted scale aides in adjusting the same clearance

on both sides.

– Finally, firmly tighten all screws of fastening kit 12 (retain-

ing adapter) and all wing nuts of fastening kit 13 (power

tool).

Operation

Working Advice

Do not overload the saw stand. Always observe the maximum

carrying capacity of the saw stand and the two table exten-

sions.

Always hold the workpiece firmly, especially the longer and

more heavy section. After cutting through the workpiece, the

centre of gravity may become dislocated in such an unfavour-

able manner that the saw stand tips over.

If possible, always place the workpiece on one or both work-

piece supports.

Extending the Saw Stand (see figures F1 – F2)

Long workpieces must be underlaid or supported at their free

end.

– Place your long workpiece onto the saw table of the power

tool.

– Loosen locking knob 17 and pull the table extension 10 out

to the desired clearance.

Due to locking pin 11, the table extension can only be

pulled out to the stop.

– Retighten the locking knobs again.

– Loosen locking knob 9 and adjust the height of the work-

piece support 8 so that the workpiece rests level.

The workpiece must be positioned level on the power

tool’s saw table.

– Retighten the locking knobs again.

Sawing Workpieces of the Same Length

(see figure G)

The material stop 6 can be used for easily sawing workpieces

to the same length.

– Adjust the desired workpiece length. (see figures F1 – F2)

– Loosen locking knob 7 and position the length stop 6 to the

desired clearance to the saw blade of the power tool.

– Retighten the locking knobs again.

Adjusting the Attachment-set Bracket

(see figure H)

After intensive use of the saw stand, the bracket that locks the

attachment set 1 to the saw table via the the locking knob 5

may possibly require readjustment.

– Remove the power tool from the attachment sets.

– Turn the attachment set upside down.

– When the attachment set cannot be locked to the saw

stand despite firmly tightening the locking knob, screw the

adjustment screw 18 in clockwise direction.

When the attachment set does not fit onto both rails (front

and rear) of the saw stand at the same time, screw the ad-

justment screw 18 in anticlockwise direction.

– Check the firm and correct seating of the attachment set

and repeat the adjustment, if required.

– Repeat the worksteps with the second attachment set.

Maintenance and Service

Maintenance

If the saw stand should fail despite the care taken in manufac-

ture and testing, repair should be carried out by an authorised

customer services agent for Bosch power tools.

In all correspondence and spare parts orders, please always

include the 10-digit article number given on the type plate of

the saw stand.

OBJ_BUCH-940-003.book Page 14 Friday, June 17, 2011 3:22 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PTA 2400 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PTA 2400 Manual

Product: