473388

Bosch PST700E Manual

10
Zoom out
Zoom in
Previous page
1/62
Next page
English–3
2 609 932 166 • (03.03) T
Ensure that the mains voltage is correct!
The voltage of the power source must agree with the
value given on the nameplate of the machine. Machines
designated for 230 V can also be operated with 220 V.
Switching On/Off
To
switch on
the machine, press the on/off switch
1
.
Lock
the depressed on/off switch
1
by pressing the
lock-on button
3
.
To
switch off
the machine, release the on/off switch
1
or push and then release it.
Continuously Variable Stroke Rate Adjustment
(PST 650 E/PST 700 E)
Light application of pressure on the on/off switch
1
re-
sults in a low stroke rate. Increasing pressure results in
a higher stroke rate.
Stroke Rate Preselection
(PST 650 E/PST 700 E)
The required stroke rate can be preselected (also dur-
ing operation) using the thumbwheel
2
.
The required stroke rate is dependent on the material
and the working conditions and can be determined by
a practical trial.
Loosen the screw
14
and slide the base plate
5
for-
ward somewhat in the direction of the saw blade. The
base plate can be swung to both sides by 45°.
Any cutting angle can be set exactly with a protrac-
tor
15
.
For the setting of precise bevel angles, the base plate
has a scale
13
with detent points in 15° steps. Slide
the rotated base plate in the direction of the blow-out
opening until it latches.
After adjusting, retighten the screw
14
.
When tightening the screw
14
, take care that the roller
guide
7
rest against the rear of the saw blade.
For sawing close to edges, the foot plate can be offset
to the rear.
Unscrew the screw
14
completely. Lift off the base
plate and reposition so that the screw
14
with the re-
tainer
18
fits in the front cut-out
17
of the base plate
and can be screwed into the threaded hole
16
.
Reposition the guide roller
7
together with the retainer
18
.
Before tightening the screw
14
, press the base plate
to the rear until it latches.
When tightening the screw 14, the guide roller 7 must
rest against the rear edge of the saw blade.
– With the base plate repositioned, the cutting angle
cannot be changed.
– The circle cutter/parallel guide 19 as well as the
splintering protector 11 cannot be used.
To prevent the splintering of the surface when sawing
wood, insert the splintering protector into the base
plate 5 from below.
The splintering protector can be used only with certain
types of saw blades.
After working for a long period with a low stroke rate, al-
low the machine to cool by running for approx. 3 minutes
without a saw blade and at maximum stroke rate.
For narrow curves, use a thin saw blade.
When sawing metal or similar material, apply a cooling
or lubricating agent along the cutting line.
/ Parallel Guide/Circle Cutter
(Accessory)
Maximum material thickness: 30 mm
/ Plunge Sawing
Plunge cutting may be used only on soft materi-
als such as wood, aerated concrete, gypsum
plaster boards, etc.!
Use only short saw blades.
Place the front edge of the base plate on the work-
piece and switch on. Press the machine firmly against
the workpiece and plunge the saw blade slowly into
the workpiece.
As soon as the complete surface of the base plate rests
on the work piece, continue to saw along the cutting line.
Putting into Operation
Adjusting the Cutting Angle
C
Offsetting the Foot Plate
Splintering Protector
Tips
D
A
E F
G H
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PST700E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PST700E in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info