766875

Bosch PST 700 ReadyToSaw Manual

5
Zoom out
Zoom in
Previous page
1/29
Next page
Français | 5
uCheck the system box and work plate for damage be-
fore each use.
uPlace the system box on a firm, non-slip, flat, hori-
zontal surface. If there is a chance that the system box
and work plate will slip or wobble, the safe and steady op-
eration of the power tool cannot be guaranteed.
Do not overload or sit/
stand on the work plate.
Overloading or standing on
the work plate can cause the
system box to tip over or
break.
uEnsure that the work plate is not unbalanced by long
workpieces or by work processes. Secure the work-
piece onto the work plate such that its centre of gravity is
over the work plate. The free end of long workpieces must
have something placed underneath it or be supported.
uDo not clamp any power tools to the work plate.
Clamped power tools and sharp-edged application tools
can cause serious injury.
uTake care not to damage the work plate and system
box when using power tools.
uDo not carry the system box by the protruding screw
clamps.
Do not stack more than three boxes on
top of each other.
uRead and observe the safety and general instructions
in the operating instructions for all tools that will be
used with the system box and the work plate.
Product Description and
Specifications
Intended Use
The work plate is intended for clamping small workpieces by
means of screw clamps.
Technical Data
Work plate for system box SystemBox with integ-
rated workbench
Article number 1 600 A01 E13
Support height mm 134
Max. load bearing capa-
city kg 15
Operation
The system box must be closed and locked at all times when
working with the work plate.
Place the non-slip mat underneath the system box. Always
secure the workpiece to the work plate using both screw
clamps. Position it such that the work area (e.g. for saw
cuts) is approx. 5–10cm from the edge of the system box.
Always hold the system box tightly in one hand when work-
ing with power tools. This will prevent the system box from
slipping or tipping over.
Maintenance and Cleaning
Keep the work plate clean to ensure effective, safe opera-
tion. Use a vacuum cleaner or damp soft cloth to remove
dirt.
Disposal
The system box and its work plate, its accessories and pack-
aging should be recycled in an environmentally friendly man-
ner.
Français
Consignes de sécurité
Lisez attentivement tous les avertisse-
ments et instructions joints au plan de tra-
vail. Le non-respect des instructions et
consignes de sécurité peut provoquer un
choc électrique, un incendie et/ou entraîner
de graves blessures.
Conservez toutes les consignes de sécuri-
té et toutes les instructions pour pouvoir
vous y reporter ultérieurement.
uAvant toute utilisation, vérifiez que la Systembox et le
plan de travail ne comportent pas de dommages.
uPlacez la Systembox sur une surface solide, plane et
horizontale. Si la Systembox risque de se déplacer ou de
basculer avec le plan de travail, il n’est pas possible de
guider l’outil électroportatif de façon uniforme et en toute
sécurité.
Ne surchargez pas le plan
de travail et ne vous ap-
puyez pas dessus. Le fait de
surcharger ou de se tenir de-
bout sur le plan de travail
peut entraîner le renverse-
ment ou le bris de la System-
box.
uAssurez-vous que le plan de travail ne risque pas
d’être déséquilibré par les pièces longues ou lors de
l’utilisation de l’outil électroportatif. Fixez la pièce sur
le plan de travail de sorte que le centre de gravité se
trouve sur la surface du plan de travail. Placez une cale
sous l’extrémité libre des pièces longues pour la suppor-
ter.
Bosch Power Tools 1 609 92A 4VR | (18.12.2018)
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PST 700 ReadyToSaw at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PST 700 ReadyToSaw in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 1,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info