Manual Bosch PST 10.8 LI T14 (page 14 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591479

Zoom out

Zoom in

1/80

14 | English

1 609 92A 0RJ | (10.11.14) Bosch Power Tools

Inserting the Saw Blade (see figure A)

 Clean the shank of the saw blade before inserting it.

An unclean shank cannot be fastened securely.

Note: The saw blade 8 can only be inserted when the SDS saw

blade receptacle 9 is open.

For jigsawing, insert the saw blade 8 with the cutting direction

toward the front; for sable sawing, insert the saw blade with

the cutting direction toward the rear. Slide it in the desired

position to the stop in the SDS saw blade receptacle 9, so that

it can be heard to engage.

Note: If you cannot insert the saw blade 8, check if the SDS

saw blade receptacle 9 is open. To open, press the SDS saw

blade receptacle 9 in the direction of the arrow.

 Check the tight seating of the saw blade. A loose saw

blade can fall out and lead to injuries.

Ejecting the Saw Blade (see figure B)

 When ejecting the saw blade, hold the machine in such

a manner that no persons or animals can be injured by

the ejected saw blade.

Press the SDS saw blade receptacle 9 in the direction of the

arrow. The saw blade is released and ejected.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Operation

Starting Operation

Inserting the battery

 Use only original Bosch lithium-ion batteries with the

voltage listed on the nameplate of your power tool.

Using other batteries can lead to injuries and pose a fire

hazard.

Note: Use of batteries not suitable for the machine can lead to

malfunctions of or cause damage to the power tool.

Insert the charged battery 2 into the handle until it can be felt

to engage and faces flush against the handle.

Switching On and Off

To switch on the power tool, first press the lock-off button 4

right or left. Then press the On/Off switch 3 and keep it

pressed.

The power light 5 lights up when the On/Off switch 3 is slightly

or completely pressed, and allows the work area to be illumi-

nated when lighting conditions are insufficient.

To switch off the power tool, release the On/Off switch 3.

To save energy, only switch the power tool on when using it.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the power tool is switched off by means of a protective

circuit: The inserted tool no longer moves.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

Controlling the Stroke Rate

Increasing or reducing the pressure on the On/Off switch 3

enables stepless stroke-rate control of the switched-on ma-

chine.

The required stroke rate is dependent on the material and the

working conditions and can be determined by a practical trial.

Reducing the stroke rate is recommended when the saw

blade engages in the material as well as when sawing plastic

and aluminium.

After longer periods of work at low stroke rate, the machine

can heat up considerably. Remove the saw blade from the ma-

chine and allow the machine to cool down by running it for ap-

prox. 3 minutes at maximum stroke rate.

Battery Charge-control Indication

The battery charge-control indicator 10 indicates the charge

condition of the battery for a few seconds when the On/Off

switch 3 is pressed half or fully through. It consists of a three-

colour illuminating LED.

Working Advice

 Before any work on the machine itself (e.g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

 When working small or thin workpieces, always use a

stable support or a saw station.

For precise work, the power tool can be used as a jigsaw; for

coarse and swift cuts, it can be used as a sabre saw. For jig-

sawing, mount the saw blade with the cutting direction to-

ward the front; for sabre sawing, mount the saw blade with

the cutting direction toward the rear.

Saw with moderate pressure in order to achieve optimal and

precise cutting results.

For long and straight cuts in thick wood, the cutting line can

become inaccurate. In this case, using a Bosch circular saw is

recommended to achieve accurate cuts.

LED Capacity

Continuous lighting, green ≥66 %

Continuous lighting, orange 33–66 %

Continuous lighting, red ≤33 %

OBJ_BUCH-1842-002.book Page 14 Monday, November 10, 2014 12:58 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PST 10.8 LI T14 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,67 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PST 10.8 LI T14 Manual

Product: