473385

Bosch PSS250AE Manual

12
Zoom out
Zoom in
Previous page
1/62
Next page
12 | English
2 609 004 199 | (30.8.11) Bosch Power Tools
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
01.09.2011
Assembly
f Before any work on the machine itself, pull the mains
plug.
Replacing the Sanding Sheet
When attaching a new sanding sheet, remove any dust or de-
bris from the sanding plate 5 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that the
punched holes in the sanding sheet match with the holes in
the sanding plate.
Sanding Sheets with Velcro Backing
(PSS 200 A/PSS 250 AE) (see figure A)
The sanding plate 5 is fitted with Velcro backing for quick and
easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 6, free the Velcro backing
of the sanding plate 5 from any debris by tapping against it in
order to enable optimum adhesion.
Position the sanding sheet 6 flush alongside one edge of the
sanding plate 5, then lay the sanding sheet onto the sanding
plate and press firmly.
To remove the sanding sheet 6, grasp it at one of the tips and
pull it off from the sanding plate 5.
Sanding Sheets without Velcro Backing
(PSS 190 AC/PSS 200 AC/PSS 250 AE) (see figure B)
Lightly lift and unlatch the sanding-sheet clamp 4.
Guide the sanding sheet 6 under the opened rear sanding-
sheet clamp 4 to the stop and clamp the sanding sheet by re-
inserting the sanding-sheet clamp 4.
Fold the sanding sheet 6 firmly around the sanding plate.
Guide the other end of the sanding sheet 6 under the front
sanding-sheet clamp 4 and clamp the sanding sheet by rein-
serting the sanding-sheet clamp 4.
Sanding sheets without holes, e. g. from rolls or by the meter,
can be punctured with the perforating tool 11 for use with
dust extraction. For this, press the machine with the mounted
sanding sheet onto the perforating tool (see figure E).
To remove the sanding sheet 6, unlatch the sanding-sheet
clamp 4 and pull out the sanding sheet.
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate
of material removal, different sanding sheets are available:
Dust/Chip Extraction
f Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suita-
ble for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
f Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Integrated Dust Extraction with Dust Box
(see figures C1–C4)
Attach the dust box 3 onto the extraction outlet 8 until it latch-
es.
To empty the dust box 3, pull off the dust box downward.
Before opening the dust box 3, it is recommended to loosen
the dust from the filter element by gently striking it against a
firm support (as shown in the figure).
Grasp the dust box 3 by the recessed grip, fold the filter ele-
ment 9 upward and empty the dust box. Clean the thin plates
of the filter element 9 with a soft brush.
External Dust Extraction (see figure D)
Mount a vacuum hose 10 onto the extraction outlet 8. Con-
nect the vacuum hose 10 with a vacuum cleaner. An overview
for the connection of various vacuum cleaners can be found at
the end of these instructions.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Engineering Director
PT/ESI
Grain size
For the working of all wooden
materials
40—240
For coarse-sanding, e. g. of
rough, unplaned beams and
boards coarse 40, 60
For face sanding and planing
small irregularities medium 80, 100, 120
For finish and fine sanding of hard
woods fine 180, 240
For the working of paint/enam-
el coats or primers and fillers
40—320
For sanding off paint coarse 40, 60
For sanding primer medium 80, 100, 120
For final sanding of primers
before coating fine 180, 240, 320
OBJ_BUCH-60-004.book Page 12 Tuesday, August 30, 2011 8:19 AM
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PSS250AE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSS250AE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info