473380
15
Zoom out
Zoom in
Previous page
1/82
Next page
English | 15
Bosch Power Tools 2 609 003 396 | (30.9.11)
Reversing the Rotational Direction (see figure C)
The rotational direction switch 10 is used to reverse the rota-
tional direction of the machine. However, this is not possible
with the On/Off switch 11 actuated.
Right Rotation: For drilling and driving in screws, push the
rotational direction switch 10 left to the stop.
The indicator for right rotation 5 lights up when the
On/Off switch 11 is actuated and the motor is run-
ning.
Left Rotation: For loosening or unscrewing screws, push the
rotational direction switch 10 right to the stop.
The indicator for left rotation 6 lights up when the
On/Off switch 11 is actuated and the motor is run-
ning.
Setting the Torque
The required torque can be preselected in 25 steps with the
torque preselection ring 3. With the correct setting, the insert
tool is stopped as soon as the screw is screwed flush into the
material or when the set torque is reached.
Select a higher setting when driving out screws, or set to the
symbol “Drilling”.
Drilling
The safety clutch is deactivated in the “Drilling” position.
Gear Selection, Mechanical
f Actuate the gear selector 4 only when the machine is at
a standstill.
Two speed ranges can be preselected with the gear selector
4.
Gear I:
Low speed range; for screwdriving or working
with large drilling diameter.
Gear II:
High speed range; for working with small drilling
diameter.
If the gear selector 4 cannot be fully engaged, lightly rotate
the drive spindle with the drill bit by twisting the drill chuck.
Switching On and Off
To start the machine, press the On/Off switch 11 and keep it
pressed.
The power light 8 lights up when the On/Off switch 11 is
slightly or completely pressed, and allows the work area to be
illuminated when lighting conditions are insufficient.
To switch off the machine, release the On/Off switch 11.
Adjusting the Speed
The speed of the switched on power tool can be variably ad-
justed, depending on how far the On/Off switch 11 is
pressed.
Light pressure on the On/Off switch 11 results in a low rota-
tional speed. Further pressure on the switch results in an in-
crease in speed.
Fully automatic spindle locking (Auto-lock)
When the On/Off switch 11 is not pressed, the drill spindle
and thus the tool holder are locked.
This enables screws to be screwed in, even when the battery
is empty and allows for the machine to be used as a screwdriv-
er.
Run-on Brake
When the On/Off switch 11 is released, the chuck brakes to a
stop, thus preventing the run-on of the tool.
When driving in screws, wait until the screw is screwed in
flush with the material and then release the On/Off switch 11.
By doing so, the head of the screw does not penetrate into the
material.
Battery Charge-control Indication
The battery charge-control indicator 9 consists of three green
LEDs, and indicates the charge condition of the battery for a
few seconds when the On/Off switch 11 is pressed halfway or
fully.
The 3 LEDs of the battery charge-control indicator 9 and the
Power Light 8 flash rapidly when the battery temperature is
not within the operating temperature range of –10 to +70°C.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be subject
to overload. When the load is too high or the allowable battery
temperature of 70 °C is exceeded, the electronic control
switches off the power tool until the temperature is in the op-
timum temperature range again.
The 3 LEDs of the battery charge-control indicator 9 and the
“Power light” 8 flash rapidly when the battery temperature is
not within the operating temperature range of –10 to +70°C
and/or when the overload protection has actuated.
Protection Against Deep Discharging
The lithium-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Working Advice
f Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
After longer periods of working at low speed, allow the ma-
chine to cool down by running it for approx. 3 minutes at max-
imum speed with no load.
For drilling in metal, use only perfectly sharpened HSS drill
bits (HSS=high-speed steel). The appropriate quality is guar-
anteed by the Bosch accessories program.
Before screwing larger, longer screws into hard materials, it is
advisable to predrill a pilot hole with the core diameter of the
thread to approx.
2
/
3
of the screw length.
LED Capacity
Continuous lighting 3 x green 71%
Continuous lighting 2 x green 3570%
Continuous lighting 1 x green 1134%
Slow flashing 1 x green 10%
OBJ_BUCH-900-002.book Page 15 Friday, September 30, 2011 10:38 AM
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PSR18 LI2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSR18 LI2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info