Manual Bosch PSR 18 LI (page 6 of 9) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

543972

Zoom out

Zoom in

1/9

6 | English

1 619 X06 940 | (22.8.11) Bosch Power Tools

Assembly

Battery Charging (see figure A)

f Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

Do not continue to press the On/Off

switch after the machine has been au-

tomatically switched off. The battery can be damaged.

To remove the battery 6, press the battery unlocking button

11 and pull the battery out of the power tool toward the rear.

Do not exert any force.

For charging, the battery 6 can also remain in the power tool.

During the charging procedure, the power tool cannot be

switched on.

The battery is equipped with a NTC temperature control

which allows charging only within a temperature range of be-

tween 0 °C and 45 °C. A long battery service life is achieved

in this manner.

Observe the notes for disposal.

Changing the Tool (see figure B)

f Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

The drill spindle is locked when the On/Off switch 9 is not

pressed. This makes quick, convenient and easy changing of

the tool in the drill chuck possible.

Open the keyless chuck 2 by turning in rotation direction n,

until the tool can be inserted. Insert the tool.

Firmly tighten the collar of the keyless chuck 2 by hand in ro-

tation direction o. This automatically locks the drill chuck.

The locking is released again to remove the tool when the col-

lar is turned in the opposite direction.

Replacing the Drill Chuck (see figures C–E)

f Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport

and storage, remove the battery from the power tool.

There is danger of injury when unintentionally actuating

the On/Off switch.

Removing the Securing Screw (see figure C)

The keyless chuck 2 is secured with a securing screw 13

against unintentional loosening from the drill spindle. Com-

pletely open the keyless chuck 2 and unscrew the securing

screw 13 in rotation direction n. Please note that the se-

curing screw has a left-hand thread.

If the securing screw 13 is seated tightly, apply a screwdriver

to the screw head and loosen the securing screw by giving a

blow onto the handle of the screwdriver.

Removing the Drill Chuck (see figure D)

Clamp the short end of an Allen key 14 into the keyless chuck

Place the machine on a stable surface (e. g. a workbench).

Hold the machine firmly and loosen the keyless chuck 2 by

turning the Allen key 14 in rotation direction n. Loosen a

tight-seated keyless chuck by giving the long end of the Allen

key 14 a light blow. Remove the Allen key from the keyless

chuck and completely unscrew the keyless chuck.

Mounting the Drill Chuck (see figure E)

The keyless chuck is mounted in reverse order.

The drill chuck must be tightened with a tightening

torque of approx. 7–9 Nm.

Screw the securing screw 13 in anti-clockwise direction into

the opened keyless chuck. Always use a new securing screw,

as the threads are covered with a thread-locking compound

that loses its effect after multiple usage.

Dust/Chip Extraction

f Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the

materials to be worked.

f Prevent dust accumulation at the workplace. Dusts can

easily ignite.

Operation

Starting Operation

Inserting the Battery

f Use only original Bosch lithium ion batteries with the

voltage listed on the nameplate of your power tool. Us-

ing other batteries can lead to injuries and pose a fire haz-

ard.

Set the rotational direction switch 8 to the centre position in

order to avoid unintentional starting. Insert the charged bat-

tery 6 into the handle so that it can be felt to engage and faces

flush against the handle.

WARNING

OBJ_BUCH-1533-001.book Page 6 Monday, August 22, 2011 5:17 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSR 18 LI in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PSR 18 LI Manual

Product: