Manual Bosch psr 14 4 li-2 (page 20 of 127) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

386452

Zoom out

Zoom in

1/127

2 609 002 432 | (3.7.07) Bosch Power Tools

20 | English

Place the machine on a stable surface (e.g. a

workbench). Hold the machine firmly and loosen

the keyless chuck 2 by turning the Allen key 16 in

rotation direction . Loosen a tight-seated key-

less chuck by giving the long end of the Allen key

16 a light blow. Remove the Allen key from the

keyless chuck and completely unscrew the key-

less chuck.

Mounting the Drill Chuck (see figure F)

The keyless chuck is mounted in reverse order.

Note: After mounting the keyless chuck, screw

the securing screw 15 in again.

The drill chuck must be tightened with a

tightening torque of approx. 7–9 Nm.

Operation

Starting Operation

Inserting the Battery

f Use only original Bosch lithium ion batteries

with the voltage listed on the nameplate of

your power tool. Using other batteries can

lead to injuries and pose a fire hazard.

Set the rotational direction switch 11 to the cen-

tre position in order to avoid unintentional start-

ing. Insert the charged battery 8 into the handle

so that it can be felt to engage and faces flush

against the handle.

Reversing the Rotational Direction

(see figure C)

The rotational direction switch 11 is used to re-

verse the rotational direction of the machine.

However, this is not possible with the On/Off

switch 12 actuated.

Right Rotation: For drilling and driving in screws,

push the rotational direction switch 11 left to the

stop.

The indicator for right rotation 5 lights up

when the On/Off switch 12 is actuated

and the motor is running.

Left Rotation: For loosening or unscrewing

screws, push the rotational direction switch 11

right to the stop.

The indicator for left rotation 6 lights up

when the On/Off switch 12 is actuated

and the motor is running.

Setting the Torque

The required torque can be preselected in 25

steps with the torque preselection ring 3. With

the correct setting, the insert tool is stopped as

soon as the screw is screwed flush into the ma-

terial or when the set torque is reached.

Select a higher setting when driving out screws,

or set to the symbol “Drilling”.

Drilling

The safety clutch is deactivated in the “Drilling”

position.

Gear Selection, Mechanical

f Actuate the gear selector 4 only when the

machine is at a standstill.

Two speed ranges can be preselected with the

gear selector 4.

Gear I:

Low speed range; for screwdriving or working

with large drilling diameter.

Gear II:

High speed range; for working with small drilling

diameter.

If the gear selector 4 cannot be fully engaged,

lightly rotate the drive spindle with the drill bit by

twisting the drill chuck.

Switching On and Off

To start the machine, press the On/Off switch 12

and keep it depressed.

The power light 9 lights up when the On/Off

switch 12 is slightly depressed, and enables illu-

mination of the screwing location in unfavourable

light conditions.

To switch off the machine, release the On/Off

switch 12

OBJ_BUCH-191-003.book Page 20 Tuesday, July 3, 2007 11:19 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch psr 14 4 li-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch psr 14 4 li-2 Manual

Product: