78134
15
Zoom out
Zoom in
Previous page
1/92
Next page
English | 152 609 001 965 11.10.06
The vibration emission level given in
this information sheet has been meas-
ured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with
another.
The vibration emission level will vary because of the
ways in which a power tool can be used and may
increase above the level given in this information sheet.
This could lead to a significant underestimate of expo-
sure when the tool is used regularly in such a way.
Note: To be accurate, an estimation of the level of
exposure to vibration experienced during a given period
of work should also take into account the times when
the tool is switched off and when it is running but not
actually doing the job. This may significantly reduce the
exposure level over the total working period.
Assembly
Battery Charging
A battery that is new or has not been used for a longer
period does not develop its full capacity until after
approx. 5 charging/discharging cycles.
To remove the battery 9 press the unlocking buttons 8
and pull out the battery downwards. Do not exert any
force.
The battery is equipped with a NTC temperature con-
trol which allows charging only within a temperature
range of between 0 °C and 45 °C. A long battery serv-
ice life is achieved in this manner.
A significantly reduced working period after charging
indicates that the battery is used and must be replaced.
Observe the notes for disposal.
Changing the Tool (see figure A)
f Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational
direction switch to the centre position. Unin-
tentional actuation of the On/Off switch can lead to
injuries.
The drill spindle is locked when the On/Off switch 12
is not pressed. This makes quick, convenient and easy
changing of the tool in the drill chuck possible.
Open the keyless chuck 1 by turning until the tool can
be inserted. Insert the tool.
Firmly tighten the collar of the keyless chuck 1 by hand
in clockwise direction until the locking action (“click”) is
no longer heard. This automatically locks the drill
chuck.
The locking is released again to remove the tool when
the collar is turned in the opposite direction.
Replacing the Drill Chuck
(see figures CE)
f Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational
direction switch to the centre position. Unin-
tentional actuation of the On/Off switch can lead to
injuries.
The keyless chuck 1 is secured with a securing screw
14 against unintentional loosening from the drill spin-
dle. Completely open the keyless chuck 1 and unscrew
the securing screw 14 in clockwise direction. Please
note that the securing screw has a left-hand
thread.
Removing the Drill Chuck (see figure D)
Clamp the short end of an Allen key 15 into the keyless
chuck 1.
Place the machine on a stable surface (e.g. a work-
bench). Hold the machine firmly and loosen the keyless
chuck 1 by turning the Allen key 15 in anticlockwise
direction. Loosen a tight-seated keyless chuck by giv-
ing the long end of the Allen key 15 a light blow.
Remove the Allen key from the keyless chuck and com-
pletely unscrew the keyless chuck.
Mounting the Drill Chuck (see figure E)
The keyless chuck is mounted in reverse order.
Note: After mounting the keyless chuck, screw the
securing screw 14 in again.
The drill chuck must be tightened with a
tightening torque of approx. 1723 Nm.
Operation
Starting Operation
Inserting the Battery
f Use only original Bosch O-pack batteries with
the voltage given on the type plate of your
machine. The use of other batteries can lead to
injuries and danger of fire.
Set the rotational direction switch 11 to the centre
position in order to avoid unintentional starting. Insert
the charged battery 9 into the handle so that it can be
felt to engage and faces flush against the handle.
Reversing the Rotational Direction (see figure B)
The rotational direction switch 11 is used to reverse the
rotational direction of the machine. However, this is not
possible with the On/Off switch 12 actuated.
Right Rotation: For drilling and driving in screws,
push the rotational direction switch 11 left to the stop.
WARNING
OBJ_BUCH-213-001.book Page 15 Wednesday, October 11, 2006 8:37 AM
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PSR 14,4-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSR 14,4-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info