Manual Bosch PSM 10.8 LI T15 (page 13 of 74) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

591473

Zoom out

Zoom in

1/74

English | 13

Bosch Power Tools 1 609 92A 0UE | (7.1.15)

Battery Charging (see figure A)

 Use only the battery chargers listed on the accessories

page. Only these battery chargers are matched to the lith-

ium-ion battery of your power tool.

Note: The battery supplied is partially charged. To ensure full

capacity of the battery, completely charge the battery in the

battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure

does not damage the battery.

The lithium-ion battery is protected against deep discharging

by the “Electronic Cell Protection (ECP)”. When the battery is

empty, the machine is switched off by means of a protective

circuit: The inserted tool no longer rotates.

 Do not continue to press the On/Off switch after the

machine has been automatically switched off. The bat-

tery can be damaged.

Note: If the machine should automatically switch off because

of a discharged or overheated battery, make sure to set the

machine’s On/Off switch 2 to off. Charge the battery and al-

low it to cool down before restarting the machine. Otherwise

the battery can become damaged.

To remove the battery 3, press the unlocking buttons 4 and

pull the battery out of the machine to the rear. Do not exert

any force.

Observe the notes for disposal.

Dust/Chip Extraction

 Dusts from materials such as lead-containing coatings,

some wood types, minerals and metal can be harmful to

one’s health. Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory infections of

the user or bystanders.

Certain dusts, such as oak or beech dust, are considered

as carcinogenic, especially in connection with wood-treat-

ment additives (chromate, wood preservative). Materials

containing asbestos may only be worked by specialists.

– As far as possible, use a dust extraction system suitable

for the material.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the mate-

rials to be worked.

 Prevent dust accumulation at the workplace. Dusts can

easily ignite.

External Dust Extraction (see figure B–C)

When working without dust extraction, please plug the outlet

piece 8 with the dust protection cap 9.

When working with dust extraction, remove the dust protec-

tion cap 9. Insert the extraction adapter 10 into the outlet

piece 8. A suction hose with a diameter of 19 mm can be con-

nected to the extraction adapter 10.

An overview for connecting to different vacuum cleaners can

be found at the end of these operating instructions.

The vacuum cleaner must be suitable for the material being

worked.

When vacuuming dry dust that is especially detrimental to

health or carcinogenic, use a special vacuum cleaner.

Replacing the Sanding Sheet (see figure D)

When attaching a new sanding sheet, remove any dust or de-

bris from the sanding plate 6 (e. g. with a brush).

To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.

The sanding plate 6 is fitted with Velcro backing for quick and

easy fastening of sanding sheets with Velcro adhesion.

Before attaching the sanding sheet 5, free the Velcro backing

of the sanding plate 6 from any debris by tapping against it in

order to enable optimum adhesion.

The machine is fitted with 2 sanding sheets that can be

changed individually, depending on the degree of wear.

 Only use the machine when both sanding sheets are

mounted.

 Only use sanding sheets with the same grain size.

Position the sanding sheet 5 flush alongside one edge of the

sanding plate 6, then lay the sanding sheet onto the sanding

plate and press firmly.

To remove the sanding sheet 5, grasp it at one of the tips and

pull it off from the sanding plate 6.

Sanding sheets of the Bosch Delta Sander can be used.

Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Selecting the Sanding Sheet

Depending on the material to be worked and the required rate

of material removal, different sanding sheets are available:

For reworking or polishing, especially of metal and stone, use

fleece/polishing cloth pad.

Depending on the desired surface quality of the workpiece,

different fleece types or polishing cloth pads are to be used.

Replacing the Sanding Plate

The supplied sanding plate 6 consists of two parts: base and

replaceable front triangle. The front triangle is fitted with Vel-

cro backing and can be replaced. To remove the sanding plate

front triangle, grasp it at one of the tips and pull it off.

Grain size

For the working of all types of materi-

als such as wood, paint, filler, lacquer,

hard and soft wood as well as chip-

boards and metal.

40–180

For coarse-sanding, e. g. of rough, un-

planed beams and boards

coarse 40

For face sanding and planing small ir-

regularities

medium 80, 120

For finish and fine sanding of hard

woods

fine 180

OBJ_BUCH-1531-003.book Page 13 Wednesday, January 7, 2015 10:29 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSM 10.8 LI T15 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PSM 10.8 LI T15 Manual

Product: