389184
11
Zoom out
Zoom in
Previous page
1/60
Next page
English - 4
Loosening the Drill Chuck
(see figure )
Place the machine on a stable surface (e. g.
workbench). Hold the machine firmly and loosen
the chuck by turning to the left, as when unscrew-
ing a screw (
). Loosen a tight chuck by giving
the long end of the Allen key 16 a sharp blow.
Tightening the Drill Chuck
(see figure )
The drill chuck is mounted in reverse order (
).
The chuck must be tightened with a torque of
approx. 3540 Nm.
Speed as well as torque setting depend on the
material and can be determined by practical test-
ing. Always start with the lowest setting.
After longer periods of working at low speed, al-
low the machine to cool down by running for ap-
prox. 3 minutes at maximum speed with no load.
For drilling in tiles, set the selector switch 2 to the
symbol “Drilling and Screwdriving”. Do not switch
over to the symbol “Impact Drilling” or work with
impact until after drilling through the tile.
Carbide tipped drill bits are required for jobs
when working in concrete, masonry and brick
wall.
Before any work on the machine itself, pull the
mains plug.
For safe and proper working, always keep the
machine and the ventilation slots clean.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts orders,
please always include the 10-digit order number
given on the nameplate of the machine.
WARNING! Important instructions for con-
necting a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to
the following code:
Do not
connect the blue or brown wire to the
earth terminal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this machine, it must
be disposed of safely.
Measured values determined according to
EN 50 144.
Typically the A-weighted noise levels of the prod-
uct are: sound pressure level: 96 dB (A); sound
power level: 109 dB (A).
Wear hearing protection!
The typical weighted acceleration is 11 m/s
2
.
Recycle raw materials instead of disposing as
waste
The machine, accessories and packaging should
be sorted for environmental-friendly recycling.
These instructions are printed on recycled paper
manufactured without chlorine.
The plastic components are labelled for catego-
rized recycling.
We declare under our sole responsibility that
this product is in conformity with the following
standards or standardization documents:
EN 50 144 according to the provisions of the di-
rectives 89/336/EEC, 98/37/EC.
Dr. Gerhard Felten Dr. Eckerhard Strötgen
Senior Vice President Engineering Head of Product Certification
Robert Bosch GmbH, Geschäftsbereich Elektrowerkzeuge
Subject to change without notice
Tips
Maintenance and Cleaning
G
H
strain relief
live = brown
neutral = blue
To be fitted
by qualified
professional only
Noise/Vibration Information
Environmental Protection
Declaration of Conformity
11 • 2 609 932 245 • 02.07
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch psb 850 2 ra at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch psb 850 2 ra in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info