386424
10
Zoom out
Zoom in
Previous page
1/68
Next page
English - 2
Measured values determined according to
EN 60 745.
Typically the A-weighted noise levels of the ma-
chine are: sound pressure level 97 dB (A); sound
power level 108 dB (A). Measurement
uncertainty K = 3 dB.
Wear hearing protection!
The typically weighted acceleration is 13 m/s
2
.
Read all instructions. Failure to
follow all instructions listed below
may result in electric shock, fire
and/or serious injury.
Additionally, the general safety instructions either
in the enclosed booklet or those added in the
centre of these operating instructions must be ob-
served.
SAVE THESE INSTRUCTIONS.
When working with the machine, always
hold it firmly with both hands and provide
for a secure stance. The power tool is guided
more secure with both hands.
Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
securely than by hand.
Do not work materials containing asbes-
tos. Asbestos is considered carcinogenic.
Always wait until the machine has come to
a complete stop before placing it down. The
tool insert can jam and lead to loss of control
over the power tool.
Do not use a machine with a damaged
mains cable. Do not touch the damaged ca-
ble and pull the mains plug when the cable
is damaged while working. Damaged cables
increase the risk of an electric shock.
Connect machines that are used in the
open via a residual current device (RCD).
Wear hearing protection when working
with impact drills. Exposure to noise can
cause hearing loss.
Always use the auxiliary handle supplied
with the machine. Loss of control can cause
personal injury.
Use suitable detectors to determine if util-
ity lines are hidden in the work area or call
the local utility company for assistance.
Contact with electric lines can lead to fire and
electric shock. Damaging a gas line can lead
to explosion. Penetrating a water line causes
property damage or may cause an electric
shock.
Switch off the power tool immediately
when the tool insert jams. Be prepared for
high reaction torque which causes kick-
back. The tool insert jams when:
– the power tool is subject to overload or
– it becomes wedged in the workpiece.
Hold the power tool only by the insulated
gripping surfaces when performing an op-
eration where the cutting tool may contact
hidden wiring or its own power cord. Con-
tact with a “live” wire will also make exposed
metal parts of the power tool “live” and shock
the operator.
The machine is intended for impact drilling in
brick, concrete and stone as well as for drilling in
wood, metal, ceramics and plastics. Machines
with electronic control and right/left rotation are
also suitable for screwdriving and thread-cutting.
The auxiliary handle can be mounted on the left
or right side of the spindle collar, using the wing
bolt 10.
The drilling depth can be set with the depth
stop 12.
For this, press the push-button for the depth-stop
adjustment 9, adjust the required drilling depth X
and release the push-button for the depth-stop
adjustment 9 again.
The ribbing on depth stop 12 must point upwards.
Noise/Vibration Information
For Your Safety
Intended Use
Auxiliary Handle/Depth Stop
(see figure )
A
2 609 932 193.book Seite 2 Mittwoch, 23. Februar 2005 2:23 14
10 • 2 609 932 193 • TMS • 08.02.05
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch psb 750-2 re at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch psb 750-2 re in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info