Manual Bosch PSB 18 LI 2 Ergonomic (page 16 of 203) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian)

766777

Zoom out

Zoom in

1/203

16 | English

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

Inserting the battery

Set the rotational direction switch (6) to the centre position

to protect the power tool from being switched on accident-

ally.

Slide the charged battery (9) from behind into the foot of

the power tool. Press the battery fully into the foot until the

battery is securely locked.

Setting the rotational direction (see figureB)

The rotational direction switch (6) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (5) is being pressed.

Clockwise: To drill and to drive in screws, press the rota-

tional direction switch (6) all the way to the front.

Anti-clockwise: To loosen or unscrew screws, press the ro-

tational direction switch (6) all the way to the back.

Preselecting the Torque

The torque presetting ring (2) can be used to preselect the

required torque in 20 stages. When the correct setting is

used, the application tool will be stopped as soon as the

screw is driven flush into the material or as soon as the set

torque has been reached. In position the overload clutch

is deactivated, e.g. for drilling or driving in very large screws.

When unscrewing screws, it may be advisable to select a

higher setting or the symbol.

Setting the operating mode (see figure C)

The operating mode presetting ring (3) can be used to

choose between screwdriving, drilling and impact drilling.

In the "impact drilling" position the overload clutch is deac-

tivated and it is constantly at maximum power.

Mechanical gear selection

uYou can press the gear selector switch (4) with the

power tool off or on. You should not do this at full load

or maximum torque, however.

You can preselect two speed ranges with the gear selector

(4).

If the gear selector switch (4) cannot be pushed all the way,

turn the drill chuck slightly with the drill.

First gear:

Low speed range; for working with a large drilling diameter

or for screwdriving.

Second gear:

High speed range; for working with a small drilling diameter.

Switching on/off

To start the power tool, press and hold the on/off switch

(5).

To switch off the power tool, release the on/off switch (5).

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when

it is on by pressing in the on/off switch (5) to varying ex-

tents.

Applying light pressure to the on/off switch (5) results in a

low rotational speed/impact rate. Applying increasing pres-

sure to the switch increases the speed/impact rate.

Emergency switch-off (KickBack Control)

The rapid shut-off function (KickBack Con-

trol) gives the user greater control over the

power tool and offers them better protec-

tion than power tools that do not have Kick-

Back Control. The power tool will switch off if it suddenly

and unforeseeably rotates around the drilling axis.

Rapid shut-off is indicated by the LED on the power tool

flashing.

To switch the tool back on, release the on/off switch and

then press it again.

uIt will no longer be possible to switch the power tool

on if the KickBack Control function is faulty. Have the

power tool serviced by a qualified repair person using

only original replacement parts.

Fully automatic spindle lock (Auto-Lock)

The drill spindle, and therefore the tool holder , are locked

when the on/off switch (5) is not pressed.

This enables screws to be screwed in even when the battery

(9) is empty and allows the power tool to be used as a

screwdriver.

Run-out brake

Upon releasing the on/off switch (5), the drill chuck is

slowed down, which prevents the application tool from con-

tinuing to rotate.

When driving in screws, you should therefore only release

the on/off switch (5) once the screw has been inserted flush

into the workpiece. This way, the head of screw will not pen-

etrate the workpiece.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or the permitted bat-

tery temperature is exceeded, the electronics of the power

tool will switch off until the temperature returns to within the

optimum operating temperature range.

1 609 92A 6DE | (16.06.2021) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSB 18 LI 2 Ergonomic in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 4,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PSB 18 LI 2 Ergonomic Manual

Product: