78234
19
Zoom out
Zoom in
Previous page
1/107
Next page
English | 19
Bosch Power Tools 1 609 929 M27 | (7.8.07)
Operation
Starting Operation
Inserting the Battery (see figure D)
f Use only original Bosch O-pack batteries
with the voltage given on the type plate of
your machine. The use of other batteries can
lead to injuries and danger of fire.
Set the rotational direction switch 6 to the centre
position in order to avoid unintentional starting.
Insert the charged battery 8 into the handle so
that it can be felt to engage and faces flush
against the handle.
Reversing the Rotational Direction
(see figure E)
The rotational direction switch 6 is used to re-
verse the rotational direction of the machine.
However, this is not possible with the On/Off
switch 7 actuated.
Right Rotation: For drilling and driving in screws,
push the rotational direction switch 6 left to the
stop.
The rotation direction indicator 5 lights up
green.
Left Rotation: For loosening and unscrewing
screws and nuts, press the rotational direction
switch 6 through to the right stop.
The rotation direction indicator 5 lights up
red.
Setting the Operating Mode
Drilling and Screwdriving
Set the selector switch 4 to the “Drill-
ing” symbol.
Impact Drilling
Set the selector switch 4 to the “Impact
drilling” symbol.
The selector switch 4 engages noticeably and
can also be actuated with the machine running.
Switching On and Off
To start the machine, press the On/Off switch 7
and keep it depressed.
To switch off the machine, release the On/Off
switch 7.
Setting the Speed/Impact Rate
The speed/impact rate of the switched on power
tool can be variably adjusted, depending on how
far the On/Off switch 7 is pressed.
Light pressure on the On/Off switch 7 results in
low speed/impact rate. Further pressure on the
switch increases the speed/impact rate.
Operating Instructions
f Apply the power tool to the screw/nut only
when it is switched off. Rotating tool inserts
can slip off.
Tips
The required speed depends on the material to be
worked and the diameter of the tool. Determine
the optimum setting through practical testing.
After longer periods of working at low speed, allow
the machine to cool down by running it for approx.
3 minutes at maximum speed with no load.
For drilling in tiles, set the selector switch 4 to
the “Drilling” symbol. Do not switch over to the
symbol “Impact Drilling” or work with impact un-
til after drilling through the tile.
Use carbide tipped drill bits when working in
concrete, masonry and brick wall.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
f For safe and proper working, always keep
the machine and ventilation slots clean.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article number
given on the type plate of the machine.
OBJ_BUCH-14-002.book Page 19 Tuesday, August 7, 2007 9:42 AM
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PSB 14.4 V-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSB 14.4 V-1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,22 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info