Manual Bosch PSB 1000-2 RCA (page 21 of 120) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

78649

Zoom out

Zoom in

1/120

English | 212 609 002 333 • 4.6.07

Open the keyless chuck 1 by turning in rotation direc-

tion n, until the tool can be inserted. Insert the tool.

Firmly tighten the collar of the keyless chuck 1 by hand

in rotation direction o until the locking action (“click”)

is no longer heard. This automatically locks the chuck.

The locking is released again to remove the tool when

the collar is turned in the opposite direction.

Keyless Chuck (PSB 700-2 RE) (see figure G)

Hold the rear sleeve 26 of the keyless chuck 1 tight and

turn the front sleeve 25 in rotation direction n, until the

tool can be inserted. Insert the tool.

Hold the rear sleeve 26 of the keyless chuck 1 tight and

firmly turn the front sleeve 25 in rotation direction o by

hand until the locking action is no longer heard. This

automatically locks the drill chuck.

The locking is released again to remove the tool when

the front sleeve 25 is turned in the opposite direction.

Screwdriver Tools (see figures H–I)

When working with screwdriver bits 27, a universal bit

holder 28 should always be used. Use only screwdriver

bits that fit the screw head.

For driving screws, always position the “Drilling/Impact

Drilling” selector switch 2 to the “Drilling” symbol.

Replacing the Drill Chuck

f Before any work on the machine itself, pull

the mains plug.

Removing the Drill Chuck (see figure J)

Disassemble the auxiliary handle and set the gear

selector 11 to the centre position between the 1st and

2nd gear.

Insert a steel pin with a diameter of Ø 4 mm and

approx. 50 mm of length into the drill hole on the spin-

dle neck in order to lock the drill spindle.

Clamp the short end of an Allen key 29 into the keyless

chuck 1.

Place the machine on a stable surface (e.g. a work-

bench). Hold the machine firmly and loosen the keyless

chuck 1 by turning the Allen key 29 in rotation direction

n. Loosen a tight-seated keyless chuck by giving the

long end of the Allen key 29 a light blow. Remove the

Allen key from the keyless chuck and completely

unscrew the keyless chuck.

Mounting the Drill Chuck (see figure K)

The keyless chuck is mounted in reverse order.

Remove the steel pin from the drill hole on the

spindle neck after mounting is completed.

The drill chuck must be tightened with a

tightening torque of approx. 50–55 Nm.

Operation

Starting Operation

f Observe correct mains voltage! The voltage of

the power source must agree with the voltage

specified on the nameplate of the machine.

Power tools marked with 230 V can also be

operated with 220 V.

Stand by Indicator (PSB 1000-2 RCE/

PSB 1000-2 RCA)

The stand by indicator 5 lights up when the mains plug

is plugged in and mains voltage is available. When the

machine cannot be started even though the stand by

indicator is lit, it must be taken to an authorized after-

sales service agent for Bosch power tools.

Reversing the Rotational Direction (see figure L)

The rotational direction switch 10 is used to reverse the

rotational direction of the machine. However, this is not

possible with the On/Off switch 9 actuated.

Right rotation: Press the rotational direction switch

10 through to the right stop (for drilling and driving

screws).

PSB 1000-2 RCE/PSB 1000-2 RCA: The indicator

for right-hand rotation 3 lights up.

PSB 700-2 RE/PSB 780-2 RE/PSB 800-2 RA: The

indicator for right-hand rotation 31 indicates the

selected rotational direction.

Left rotation: Press the rotational direction switch 10

through to the left stop (for loosening and unscrewing

screws and nuts).

PSB 1000-2 RCE/PSB 1000-2 RCA: The indicator

for left-hand rotation 4 lights up.

PSB 700-2 RE/PSB 780-2 RE/PSB 800-2 RA: The

indicator for left-hand rotation 32 indicates the selected

rotational direction.

Setting the Operating Mode

Drilling and Screwdriving

Set the selector switch 2 to the “Drilling”

symbol.

Impact Drilling

Set the selector switch 2 to the “Impact drill-

ing” symbol.

The selector switch 2 engages noticeably and can also

be actuated with the machine running.

Switching On and Off

To start the machine, press the On/Off switch 9 and

keep it depressed.

To lock the pressed On/Off switch 9, press the lock-

on button 8.

OBJ_BUCH-79-006.book Page 21 Monday, June 4, 2007 4:08 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSB 1000-2 RCA in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PSB 1000-2 RCA Manual

Product: