Manual Bosch PRP626B70N (page 6 of 24) (English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish)

533051

Zoom out

Zoom in

1/24

Read the appliance's instructions before

installing and using.

The graphics in these Assembly

instructions are given as a guide only.

The manufacturer is exempt from all

liability if this manual's requirements

are not complied with.

Safety instructions

All operations relating to installation,

regulation and conversion to other

types of gas must be carried out by

an authorised installation engineer,

respecting applicable regulations,

standards and the specifications of

the gas and electricity providers.

Before you begin, turn off the

appliance's electricity and gas

supply.

You are recommended to contact the

Technical Assistance Service to

convert to another type of gas.

This appliance has been designed for

home use only, not for commercial or

professional use. This appliance cannot

be installed on yachts or in caravans.

The warranty will only be valid if the

appliance is used for the purpose for

which it was designed.

Before installing, you need to check that

local distribution conditions (gas type

and pressure) and the appliance's

adjustment are compatible (see table I).

The appliance's adjustment conditions

are written on the label or the

specifications plate.

This appliance can only be installed in a

well-ventilated place in accordance with

existing regulations and ventilation

specifications. The appliance must not

be connected to a combustion product

evacuation device.

The supply cable must be attached to

the unit to prevent it from touching hot

parts of the oven or hob.

Appliances with electrical supply must

be earthed.

Do not tamper with the appliance's

interior. If necessary, call our Technical

Assistance Service.

Before installing

This appliance is class 3 type, according

to the EN 30-1-1 regulation for gas

appliances: built-in appliance.

The units next to the appliance must be

made of non-inflammable materials. The

laminated covering and glue for

adhering it must be heat resistant.

This appliance cannot be installed

above fridges, washing machines,

dishwashers or similar.

An oven must have power cooling fan to

install a hob above it.

Check the oven's dimensions in its

installation manual.

If an extractor fan is installed, you must

follow the installation manual's

instructions, always keeping a minimum

distance of 650 mm to the hob.

Preparation of unit (fig. 1-2)

Make a cut of an appropriate size in the

work surface.

If the hob is electric or mixed (gas and

electricity) and there is no oven below,

place a non-inflammable separator

(e.g.metal or plywood) 10 mm from the

bottom of the hob. This will prevent

access to the base of the hob. If the hob

is gas, it is recommendable to place the

separator at the same distance.

On wooden work surfaces, varnish the

cutting surfaces with a special glue to

protect them from moisture.

Installation of appliance

The clips and the adhesive seal

(underside of the hob) are factory-fitted,

do not under any circumstances remove

them. The seal ensures that the entire

work surface will be watertight, and

prevents water seepage. In order to fit

the appliance into the kitchen unit, first

place the hob in the correct position then

loosen each of the clips so that

they all turn freely (it is not necessary to

completely undo them). Fit and centre

the hob.

Press the sides of the hob until it is

supported around its entire perimeter.

Turn the clips and tighten them fully.

Fig. 3.

Removing the hob

Turn off the electricity and gas supply to

the appliance.

Unscrew the clips and proceed in the

reverse order to installation.

Gas connection (fig. 4)

The end of the inlet connection point of

the gas hob has a 1/2” (20.955 mm)

thread that allows for:

- rigid connection.

- connection using a flexible metal hose

(L min. 1 m - max. 3 m). With this option,

you must prevent the hose from coming

into contact with the moving parts of the

kitchen unit (for example, a drawer) or

accessing any spaces which might

become obstructed.

If you need to make a cylindrical

connection, replace the factory-fitted L-

tube with the one in the accessory bag.

Fig. 4a.

Please remember to insert the seal.

Warning! If any connection is handled,

check for tightness. Danger of leaks.

The manufacturer shall not be held liable

if any connection should leak, after

being handled.

Electric connection (fig. 5)

Check the voltage and power of the

appliance are compatible with the

electrical installation.

The hobs are supplied with a power

cable with or without a wall socket plug.

Provide an omnipolar cut-off switch with

a minimum contact gap of 3 mm (except

for plug connections, if the user has

access to it).

Appliances with plugs must only be

connected to sockets that have earth

wires correctly installed.

This appliance is type “Y”: the input

cable can only be changed by the

Technical Assistance Service and not

the user. The cable type and minimum

cross-section must be respected.

Changing the gas type

If the country’s regulations permit, this

appliance can be adapted to other types

of gas (see specifications plate). The

components necessary for this are in the

transformation kit supplied (according to

model). The kit is also available from our

Technical Assistance Service. The

following steps should be taken:

A) Changing the rapid, semi-rapid

and auxiliary burner nozzles (fig. 6):

- Remove the pan supports, the covers

and the gas burner casing.

- Change the burner nozzles using the

spanner provided by our Technical

Assistance Service (code 424699)

taking special care to ensure that the

burner nozzle does not fall when it is

removed from the burner or when fitted.

Ensure that they are completely

tightened in order to guarantee the seal.

Primary air adjustment is not necessary

with these burners.

B) Changing the double flame burner

nozzles (Fig. 7):

The glass panel and the frame are fixed

to the rest of the surface by means of

clips. The following steps must be taken

to remove both the glass panel and

frames:

- Remove the pan supports, covers, gas

burner casing, etc. Fig. 7a.

- Loosen the two screws on the rapid,

semi-rapid and auxiliary burners.

- Loosen the three screws on the double

flame burner. Fig. 7b - 7c.

- Use the disassembly lever 483196,

supplied by our technical services

department. To release the front clips,

use the lever at the points indicated in

figures 8, according to the hob model.

Never use the lever on the glass edges

which have no frame or trim!

- To release the rear clips, lift the glass

panel and frame carefully according to

Fig. 8.

Changing the outer flame nozzle.

Loosen the locking screw L1, fig. 9a, to

remove the bushing L2, backwards.

Remove the outer flame nozzle by

turning it towards the left.

Meanwhile, hold the nozzle housing.

Fig. 8b.

Screw in the new outer flame nozzle,

holding the nozzle housing in the

opposite direction.

Adjust the airflow adjusting bushing L2

according to the value -Z- shown in table

II. Tighten the locking screw L1.

Changing the inner flame nozzle.

Unscrew the part M3. from the threaded

part M2.

To do this, hold the threaded part in the

opposite direction. See Fig. N. Then

unscrew the threaded part M2. from part

M1, holding in the opposite direction.

See Fig. O.

Unscrew the inner flame nozzle M4 from

the part M2 and replace it with the

appropriate nozzle as indicated in table

II and adjust the airflow adjusting

bushing M5 according to the value -Y-

indicated in table II.

If the appliance is not securely fastened

or the clips are too rigid it may cause the

appliance to lift up. The procedure to be

followed in this situation is as follows:

1) Release the clips fixing the appliance

to the kitchen unit.

2) Loosen the main gas connection and

remove the appliance from its location.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PRP626B70N in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PRP626B70N

Bosch PRP626B70N User Manual - Dutch - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PRP626B70N Manual

Product: