Manual Bosch PowerPack 400 Active Line (page 10 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

657519

Zoom out

Zoom in

1/56

English–3

0 275 007 XPX | (5.4.16) Bosch eBike Systems

Using Two Battery Packs for One eBike (optional)

An eBike can also be equipped with two battery packs by the

manufacturer. In this case, one of the charge sockets is not

accessible or is sealed by the bicycle manufacturer with a

sealing cap. Charge the battery packs only at the accessible

charge socket.

 Never open charge sockets that have been sealed by

the manufacturer. Charging at a previously sealed charge

socket can lead to irreparable damage.

If you have an eBike that is designed for two battery packs and

you want to use it with only battery pack, cover off the con-

tacts of the unused socket using the cover lid 10 provided be-

cause otherwise the open contacts pose a risk of short-cir-

cuiting (see figures A and B).

Charging with Two Battery Packs Inserted

If two battery packs are mounted on one eBike, both battery

packs can be charged using the unsealed connection. The

charging process will charge both battery packs alternately,

automatically switching between both battery packs numer-

ous times. The charging times add up.

Both battery packs are also discharged alternately during

operation.

If you take the battery packs out of the holders, you can

charge each battery pack individually.

Charging with One Battery Pack Inserted

If only one battery pack is inserted, then you can charge only

the battery pack that has the accessible charge socket on the

bike. You can charge the battery pack with the sealed charge

socket only when you take the battery pack out of the holder.

Inserting and removing the battery pack

(see figures A–B)

 Always switch off the battery pack and the eBike sys-

tem when you insert the battery pack into the holder or

when you take it out of the holder.

In order for the battery pack to be inserted, the key 5 must be

inserted into the lock 6 and the lock must be unlocked.

To insert the standard battery pack 8, place it with the con-

tacts on the lower holder 9 on the eBike (the battery pack can

be inclined up to 7° to the frame). Tilt it into the upper holder

7 until it engages.

To insert the rack-type battery pack 2, slide it with the con-

tacts facing ahead until it engages in the holder 1 of the rear

rack/carrier.

Check if the battery pack is tightly seated. Always lock the

battery pack with lock 6, as otherwise the lock can open and

the battery pack could fall out of the holder.

After locking, always remove the key 5 from the lock 6. This

prevents the key from falling out and the battery pack from

being removed from unauthorised persons when the eBike is

parked.

To remove the standard battery pack 8, switch it off and un-

lock the lock with the key 5. Tilt the battery pack out of the up-

per holder 7 and pull it out of the lower holder 9.

To remove the rack-type battery pack 2, switch it off and

unlock the lock with the key 5. Pull the battery pack out of the

holder 1.

Operation

Initial Operation

 Use only original Bosch battery packs approved for

your eBike by the manufacturer. Using other battery

packs can lead to injuries and pose a fire hazard. When us-

ing other battery packs, Bosch shall not assume any liabil-

ity and warranty.

Switching On and Off

Switching on the battery pack is one of the ways of switching on

the eBike system. When doing so, read and observe the operat-

ing instructions of the drive unit and on-board computer.

Before switching on the battery pack or the eBike system,

check that the lock 6 is locked.

To switch on the battery pack, press the On/Off button 4. The

LEDs of indicator 3 light up and at the same time indicate the

charge condition.

Note: If the capacity of the battery pack is below 5 %, no LED

on the charge-control indicator 3 lights up. It is only visible on

the on-board computer, if the eBike system is switched on.

To switch off the battery pack, press the On/Off button 4

again. The LEDs of indicator 3 go out. This also switches off

the eBike system.

If no power is drawn from the eBike drive for about 10 min-

utes (e.g. because the eBike is not moving) and no button is

pressed on the on-board computer or the operating unit of the

eBike, the eBike system and therefore also the battery pack

will shut down automatically to save energy.

The battery pack is protected against deep discharging, over-

charging, overheating and short-circuiting through the “Elec-

tronic Cell Protection (ECP)”. In case of hazardous situations,

a protective circuit automatically switches off the battery

pack.

When a defect of the battery

pack is detected, two LEDs of

the charge-control indicator 3

flash. In this case, please refer

to an authorised Bosch eBike

dealer.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PowerPack 400 Active Line in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PowerPack 400 Active Line Manual

Product: