Manual Bosch PowerPack 400 2017 (page 13 of 70) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

780238

Zoom out

Zoom in

1/70

English–3

Bosch eBike Systems 0 275 007 XPX | (4.5.17)

Charging the Battery Pack

Use only the Bosch charger provided with your eBike or

an identical original Bosch charger. Only this charger is

matched to the lithium-ion battery pack used in your eBike.

Note: The battery pack is supplied partially charged. To en-

sure full battery pack capacity, completely charge the battery

pack in the charger before using for the first time.

For charging the battery pack, read and observe the operating

instructions of the charger.

The battery can be charged at any level of charge. Interrupting

the charging process does not damage the battery pack.

The battery pack is equipped with a temperature control indi-

cator, which enables charging only within a temperature

range between 0 °C and 40 °C.

When the battery pack is not

within the charging-tempera-

ture range, three LEDs of the

charge-control indicator 3

flash. Disconnect the battery

pack from the charger until its

temperature has adjusted.

Do not connect the battery pack to the charger until it has

reached the allowable charging temperature.

Charge-control Indicator

When the battery pack is switched on, the five green LEDs of

the charge-control indicator 3 indicate the charge condition

of the battery pack.

In this, each LED indicates approx. 20% capacity. When the

battery pack is completely charged, all five LEDs light up.

The charge level of the switched on battery pack is also shown

on the display of the on-board computer. When doing so, read

and observe the operating instructions of the drive unit and

on-board computer.

If the capacity of the battery pack is below 5 %, all LEDs of the

charge-control indicator 3 on the battery pack go out. How-

ever there is another display function of the on-board

computer.

After charging, disconnect the battery from the charger and

the charger from the network.

Using Two Battery Packs for One eBike (optional)

An eBike can also be equipped with two battery packs by the

manufacturer. In this case, one of the charge sockets is not

accessible or is sealed by the bicycle manufacturer with a

sealing cap. Charge the battery packs only at the accessible

charge socket.

Never open charge sockets that have been sealed by

the manufacturer. Charging at a previously sealed charge

socket can lead to irreparable damage.

If you have an eBike that is designed for two battery packs and

you want to use it with only battery pack, cover off the con-

tacts of the unused socket using the cover lid 10 provided be-

cause otherwise the open contacts pose a risk of short-

circuiting (see figures A and B).

Charging with Two Battery Packs Inserted

If two battery packs are mounted on one eBike, both battery

packs can be charged using the unsealed connection. The

charging process will charge both battery packs alternately,

automatically switching between both battery packs numer-

ous times. The charging times add up.

Both battery packs are also discharged alternately during

operation.

If you take the battery packs out of the holders, you can

charge each battery pack individually.

Charging with One Battery Pack Inserted

If only one battery pack is inserted, then you can charge only

the battery pack that has the accessible charge socket on the

bike. You can charge the battery pack with the sealed charge

socket only when you take the battery pack out of the holder.

Inserting and removing the battery pack

Always switch off the battery pack and the eBike

system when you insert the battery pack into the

holder or when you take it out of the holder.

Inserting and removing a standard battery (seefigure A)

In order for the battery pack to be inserted, the key 5 must be

inserted into the lock 6 and the lock must be unlocked.

To insert the standard battery pack 8, place it with the con-

tacts on the lower holder 9 on the eBike (the battery pack can

be inclined up to 7° to the frame). Tilt it into the upper holder

7 until it engages.

Check if the battery pack is tightly seated. Always lock the

battery pack with lock 6, as otherwise the lock can open and

the battery pack could fall out of the holder.

After locking, always remove the key 5 from the lock 6. This

prevents the key from falling out and the battery pack from

being removed from unauthorised persons when the eBike is

parked.

To remove the standard battery pack 8, switch it off and

unlock the lock with the key 5. Tilt the battery pack out of the

upper holder 7 and pull it out of the lower holder 9.

Inserting and removing a rack battery (seefigure B)

In order for the battery pack to be inserted, the key 5 must be

inserted into the lock 6 and the lock must be unlocked.

To insert the rack-type battery pack 2, slide it with the con-

tacts facing ahead until it engages in the holder 1 of the rear

rack/carrier.

Check if the battery pack is tightly seated. Always lock the

battery pack with lock 6, as otherwise the lock can open and

the battery pack could fall out of the holder.

OBJ_BUCH-2032-006.book Page 3 Thursday, May 4, 2017 3:28 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PowerPack 400 2017 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8.25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PowerPack 400 2017 Manual

Product: