Manual Bosch PMF 2000 CE Systeembox (page 21 of 123) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian)

766880

Zoom out

Zoom in

1/123

English | 21

uAlways wait until the power tool has come to a com-

plete stop before placing it down.

Note: Do not keep the ventilation slots (3) on the power tool

closed when working as this will reduce the service life of the

power tool.

Operating principle

The oscillating drive causes the application tool to oscillate

back and forth by 2.8° up to 20000 times per minute. This

enables precise work in the tightest of spaces.

Use a consistent, low contact pressure

when performing work; otherwise, the

performance will be impaired and the ap-

plication tool may jam.

While working, move the power tool back

and forth to prevent the application tool

overheating and jamming.

Sawing

uUse only undamaged saw blades that are in perfect

condition. Bent or dull saw blades can break, negatively

influence the cut, or lead to kickback.

uWhen sawing lightweight materials, take into account

the statutory provisions and recommendations of the

material manufacturers.

uPlunge cuts may only be applied to soft materials,

such as wood, gypsum board, etc.

Before using HCS saw blades to saw into wood, chipboard,

building materials, etc., check these saw blades for foreign

objects, such as nails, screws, etc. Remove the foreign ob-

jects as required or use bi-metal saw blades.

Cutting

Note: When cutting wall tiles, please bear in mind that the

application tools are subject to high wear if used for exten-

ded periods.

Sanding

The material removal rate and sanding result are primarily

determined by the choice of sanding sheet, the preselected

orbital stroke rate level and the contact pressure.

Only immaculate sanding sheets achieve good sanding per-

formance and make the power tool last longer.

Be sure to apply consistent contact pressure in order to in-

crease the lifetime of the sanding sheets.

Excessively increasing the contact pressure will not lead to

increased sanding performance, rather it will cause more

severe wear of the power tool and of the sanding sheet.

To sand corners, edges and hard-to-reach areas accurately,

you can also work with the tips alone or with an edge of the

sanding plate.

The sanding sheet may heat up significantly when used to

sand specific points rather than entire surfaces. Reduce the

orbital stroke rate and contact pressure and allow the sand-

ing sheet to cool down at regular intervals.

Do not use a sanding sheet for other materials after it has

been used to work on metal.

Use only original Bosch-sanding accessories.

Always connect a dust extraction system for sanding.

Scraping

Select a high orbital stroke rate level for scraping.

Work on a soft surface (e.g. wood) at a flat angle and with

low contact pressure. Failure to do so may cause the scraper

to cut into the surface underneath.

Maintenance and Service

Maintenance and Cleaning

uPull the plug out of the socket before carrying out any

work on the power tool.

uTo ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

In order to avoid safety hazards, if the power supply cord

needs to be replaced, this must be done by Bosch or by an

after-sales service centre that is authorised to repair Bosch

power tools.

Regularly clean Riff application tools (accessories) using a

wire brush.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. You can find explosion drawings and information on

spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you

with any questions about our products and their accessor-

ies.

In all correspondence and spare parts orders, please always

include the 10‑digit article number given on the nameplate

of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham Uxbridge

UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange

the collection of a product in need of servicing or repair.

Tel. Service: (0344) 7360109

E-Mail: boschservicecentre@bosch.com

You can find further service addresses at:

www.bosch-pt.com/serviceaddresses

Disposal

The power tool, accessories and packaging should be re-

cycled in an environmentally friendly manner.

Bosch Power Tools 1 609 92A 674 | (01.12.2020)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PMF 2000 CE Systeembox in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 3,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PMF 2000 CE Systeembox Manual

Product: