708261

Bosch PMF 1800 E Multitool Manual

17
Zoom out
Zoom in
Previous page
1/19
Next page
English | 17
Bosch Power Tools 1 609 92A 1PU | (13.11.15)
Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one’s health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
Connecting the Dust Extraction (see figure A)
The dust extraction 16 is intended only when working with the
sanding plate 9; it is not of use in combination with other ap-
plication tools.
For sanding, always connect the dust extraction.
To mount the dust extraction 16 (accessory), remove the ap-
plication tool and the depth stop 11.
Slide the dust extraction 16 over and beyond the tool holder
5 to the stop onto the gear head of the power tool. Insert fas-
tening screw 15 into the corresponding recess on the hous-
ing. To lock the screw, turn it to the position.
Pay attention that the felt ring 17 is undamaged and faces
tightly against the sanding plate 9. Replace a damage felt ring
immediately.
Place a vacuum hose 13 (accessory) onto the vacuum con-
nection 14. Connect the vacuum hose 13 with a vacuum
cleaner (accessory).
An overview for connecting to various vacuum cleaners can be
found on the graphics page.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
To remove the dust extraction 16, turn fastening screw 15 to
the position and pull the dust extraction from the gear
head of the power tool.
Operation
Starting Operation
Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate of
the machine.
Switching On and Off
To start the machine, push the On/Off switch 1 forward so
that the “I” is indicated on the switch.
To switch off the machine, push the On/Off switch 1 toward
the rear so that the “0” is indicated on the switch.
To save energy, only switch the power tool on when using it.
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the orbital stroke
rate 2, you can preselect the required orbital stroke rate, even
during operation.
The required stroke rate depends on the material and the
working conditions and can be determined through practical
testing.
When sawing, cutting and sanding harder materials, e.g.,
wood or metal, it is recommended to work with orbital stroke
rate “6”; for softer materials, such as plastic, orbital stroke
rate “4” is recommended.
Sanding disc Material Application Grain size
Red quality
– All wooden materials
(e. g., hardwood, soft-
wood, chipboard, build-
ing board)
– Metal materials
For coarse-sanding, e. g. of rough, unplaned beams
and boards
coarse 40
60
For face sanding and planing small irregularities
medium 80
100
120
For finish and fine sanding of wood
fine 180
240
320
400
White quality
–Paint
–Varnish
– Filling compound
– Filler
For sanding off paint
coarse 40
60
For sanding primer (e. g., for removing brush dashes,
drops of paint and paint run)
medium 80
100
120
For final sanding of primers before coating
fine 180
240
320
OBJ_BUCH-2516-002.book Page 17 Friday, November 13, 2015 9:25 AM
… 17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PMF 1800 E Multitool at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PMF 1800 E Multitool in the language / languages: French as an attachment in your email.

The manual is 3,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info