Manual Bosch PLL 360 (page 11 of 55) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian)

777050

Zoom out

Zoom in

1/55

English | 11

To open the battery compartment cover(6), press the lock-

ing mechanism(7) and lift open the battery compartment

cover. Insert the batteries/rechargeable batteries.

When inserting the batteries, ensure the polarity is correct

according to the representation on the inside of the battery

compartment cover(6).

Always replace all the batteries at the same time. Only use

batteries from the same manufacturer and which have the

same capacity.

uTake the batteries out of the measuring tool when you

are not using it for a prolonged period of time. The bat-

teries can corrode and self-discharge during prolonged

storage.

Operation

Start-up

uProtect the measuring tool from moisture and direct

sunlight.

uDo not expose the measuring tool to any extreme tem-

peratures or variations in temperature. For example,

do not leave it in a car for extended periods of time. In

case of large variations in temperature, allow the measur-

ing tool to adjust to the ambient temperature before put-

ting it into operation. The precision of the measuring tool

may be compromised if exposed to extreme temperat-

ures or variations in temperature.

uAvoid substantial knocks to the measuring tool and

avoid dropping it. Damaging the measuring tool can

cause accuracy to be compromised. If the laser line is

subjected to a substantial knock or is dropped, check it

by comparing it to a known horizontal or vertical refer-

ence line.

uSwitch the measuring tool off when transporting it.

The pendulum unit is locked when the tool is switched off,

as it can otherwise be damaged by big movements.

Switching On/Off

To switch on the measuring tool, slide the on/off switch (2)

to the "On" position. As soon as it is switched on, the meas-

uring tool emits laser lines from the outlet apertures(1).

uDo not direct the laser beam at persons or animals and

do not stare into the laser beam yourself (even from a

distance).

To switch off the measuring tool, slide the on/off switch (2)

to the "Off" position. The pendulum unit is locked when the

tool is switched off.

uNever leave the measuring tool unattended when

switched on, and ensure the measuring tool is

switched off after use. Others may be blinded by the

laser beam.

Operating Modes

Once the measuring tool has been switched on, it is in cross-

line operation with automatic levelling.

To change the operating mode, press the Modebutton for

laser operating mode (9) until the required laser operating

mode is displayed by the corresponding "Laser operating

mode" indicator(11) lighting up.

You can choose between the following operating modes:

Indicator Operating mode

Cross-line operation (see figuresA, B

andE): The measuring tool generates a ho-

rizontal laser plane (360° surrounding

laser line) and a vertical laser line.

Horizontal operation (see figureC): The

measuring tool generates a horizontal laser

plane.

Vertical operation (see figureD): The

measuring tool generates a vertical laser

line.

All operating modes can be selected with or without auto-

matic levelling.

Automatic Levelling

Working with automatic levelling (see figuresF–G)

When working with automatic levelling, the "Working without

automatic levelling" indicator(12) must not be lit. If neces-

sary, switch automatic levelling on again by pressing the

Lockbutton for switching off automatic levelling (8) so that

the "Working without automatic levelling" indicator goes out.

Position the measuring tool on a level, firm surface or attach

it to the holder(13) or the tripod(18).

The automatic levelling function automatically compensates

irregularities within the self-levelling range of ±4°. The level-

ling is finished as soon as the laser lines stop moving.

If automatic levelling is not possible, e.g. because the sur-

face on which the measuring tool stands deviates by more

than 4° from the horizontal plane, the levelling warning(10)

lights up red and the laser is switched off automatically.

If this is the case, set up the measuring tool in a level position

and wait for the self-levelling to take place. As soon as the

measuring tool is within the self-levelling range of ±4° again,

the levelling warning(10) goes out and the laser is switched

on.

It is not possible to work with automatic levelling outside the

self-levelling range of ±4°, as the laser line cannot be guaran-

teed to be perpendicular outside this range.

In case of ground vibrations or position changes during oper-

ation, the measuring tool is automatically levelled again.

Upon re-levelling, check the position of the horizontal or ver-

tical laser line with regard to the reference points to avoid er-

rors by moving the measuring tool.

Working without automatic levelling (see figureE)

To work without automatic levelling, press the Lockbutton

for switching off automatic levelling(8). The "Working

without automatic levelling" indicator(12) lights up red

when automatic levelling is switched off.

If you switch off the automatic levelling system, you can hold

the measuring tool freely in your hand or set it down on a

Bosch Power Tools 1 609 92A 4J0 | (25.01.2019)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PLL 360 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 7.28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PLL 360 Manual

Product: