383730
18
Zoom out
Zoom in
Previous page
1/101
Next page
18 | English
1 619 929 J64 | (22.2.12) Bosch Power Tools
Insert the dust/chip box 25 firmly into the chip ejector 16.
Empty the dust/chip box 25 in time to maintain optimum effi-
ciency.
To empty the dust/chip box 25, pull it off of the sawdust ejec-
tor 16. Press the slider 26 upward, turn the dust/chip box 25
aside and empty it.
Before reattaching, clean the connection sleeve of the dust/
chip box 25.
Operation
Operating Modes
f Before any work on the machine itself, pull the mains
plug.
Adjusting the Cutting Depth (see figure F)
f Adjust the cutting depth to the thickness of the work-
piece. Less than a full tooth of the blade teeth should be
visible below the workpiece.
Loosen the clamping lever 27. For a smaller cutting depth,
pull the saw away from the base plate 12; for a larger cutting
depth, push the saw toward the base plate 12. Adjust the de-
sired cutting depth at the cutting-depth scale. Tighten the
clamping lever 27 again.
Adjusting the Cutting Angle
Loosen the wing bolts 7 and 14. Tilt the saw sidewards. Ad-
just the desired measure on the scale 5. Tighten the wing
bolts 7 and 14 again.
Note: For bevel cuts, the cutting depth is smaller than the set-
ting indicated on the cutting-depth scale 28.
Cutting Marks (see figure G)
(PKS 55 A/PKS 66 A/PKS 66 AF)
The “CutControl” 9 viewing window, which folds out to the
front, is used for precise guiding of the circular saw alongside
the cutting line on the workpiece. The “CutControl” 9 viewing
window has a mark each for right-angled cuts and for 45°
cuts.
The 0° cutting mark (30) indicates the position of the saw
blade for right-angled cuts. The 45° cutting mark (29) indi-
cates the position of the saw blade for 45° cuts.
For precise cuts, position the circular saw against the work-
piece as shown in the figure. It is best to carry out a trial cut.
Cutting Marks (PKS 55)
The 0° cutting mark (30) indicates the position of the saw
blade for right-angled cuts. The 45° cutting mark (29) indi-
cates the position of the saw blade for 45° cuts.
For precise cuts, position the circular saw against the work-
piece as shown in the figure. It is best to carry out a trial cut.
Starting Operation
f Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 1 and then press the On/Off switch 2 and keep
it pressed.
To switch off the machine, release the On/Off switch 2.
Note: For safety reasons, the On/Off switch 2 cannot be
locked; it must remain pressed during the entire operation.
When not using the power tool, switch it off in order to save
energy.
Working Advice
Protect saw blades against impact and shock.
Guide the machine evenly and with light feed in the cutting di-
rection. Excessive feed significantly reduces the service life of
the saw blade and can cause damage to the power tool.
Sawing performance and cutting quality depend essentially
on the condition and the tooth form of the saw blade. There-
fore, use only sharp saw blades that are suited for the material
to be worked.
Sawing Wood
The correct selection of the saw blade depends on the type
and quality of the wood and whether lengthway or crossway
cuts are required.
When cutting spruce lengthways, long spiral chips are
formed.
Beech and oak dusts are especially detrimental to health.
Therefore, work only with dust extraction.
3029
OBJ_BUCH-841-006.book Page 18 Wednesday, February 22, 2012 3:44 PM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch pks 66 a at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch pks 66 a in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info