Manual Bosch PHO20_82 (page 19 of 106) (Dutch, Danish, Swedish, Turkish, Norwegian, Finnish)

21838

Zoom out

Zoom in

1/106

English | 19

Bosch Power Tools 2 609 932 743 | (4.12.09)

Operation

Operating Modes

Adjusting the Planing Depth

With the adjustment knob 2, the planing depth

can be adjusted variably from 0–2.0 mm using

the planing depth scale 3

(scale graduation = 0.1 mm).

Park Rest (see figure G)

The park rest 25 allows the machine to be set

down directly after operation, without danger of

damaging the working surface or the planer

blade. While planing, the park rest 25 is tilted

upwards thus enabling full contact of the rear

part of the planer base plate 8.

Note: The park rest 25 may not be removed.

Starting Operation

f Observe correct mains voltage! The voltage

of the power source must agree with the

voltage specified on the nameplate of the

machine. Power tools marked with 230 V

can also be operated with 220 V.

Switching On and Off

To start the machine, first push the lock-off but-

ton for the On/Off switch 6 and then press the

On/Off switch 5 and keep it pressed.

To switch off the machine, release the On/Off

switch 5.

Note: For safety reasons, the On/Off switch 5

cannot be locked; it must remain pressed during

the entire operation.

Working Advice

Planing (see figure G)

Set the required planing depth and place the

front part of the planer base plate 8 against the

workpiece.

f Apply the machine to the workpiece only

when switched on. Otherwise there is dan-

ger of kickback when the cutting tool jams in

the workpiece.

Switch the machine on and guide the machine

with even feed over the surface to be planed.

To achieve high-grade surfaces, work only with

low feed and apply pressure on the centre of the

planer base plate.

When machining hard materials (e.g. hard-

wood) as well as when utilising the maximum

planer width, set only low planing depths and

reduce planer feed, as required.

Excessive feed reduces the surface quality and

can lead to rapid clogging of the chip ejector.

Only sharp blades achieve good cutting capacity

and give the machine longer life.

The integrated park rest 25 also allows for con-

tinued planing at any given location on the work-

piece after an interruption:

– With the park rest folded down, place the

machine on the location of the workpiece

where the planing is to be continued.

– Switch on the machine.

– Apply the supporting pressure onto the front

part of the planer base plate and slowly push

the machine forward (n). This tilts the park

rest upward (o) so that the rear part of the

planer base plate faces on the workpiece

again.

– Guide the machine over the surface to be

planed (p) with even feed.

Beveling Edges (see figure H)

The V-grooves in the front planer base plate al-

low quick and easy beveling of workpiece edges.

Depending on required bevel width, use the cor-

responding V-groove. For this, place the planer

with the V-groove onto the edge of the work-

piece and guide it along the edge.

Groove to be

used

Dimension a

(mm)

none 0 – 2.5

small 1.0 – 4.5

medium 2.0 – 5.0

large 2.5 – 6.0

OBJ_BUCH-631-002.book Page 19 Friday, December 4, 2009 10:00 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PHO20_82 in the language / languages: Dutch, Danish, Swedish, Turkish, Norwegian, Finnish as an attachment in your email.

The manual is 3,32 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PHO20_82

Bosch PHO20_82 User Manual - English, German, French, Italian, Portuguese, Spanish - 64 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PHO20_82 Manual

Product: