382830
18
Zoom out
Zoom in
Previous page
1/106
Next page
18 | English
2 609 932 703 | (14.9.09) Bosch Power Tools
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, press the On/Off switch 5
and keep it pressed.
To lock the pressed On/Off switch 5, press the
lock-on button 6.
To switch off the machine, release the On/Off
switch 5 or when it is locked with the lock-on
button 6, briefly press the On/Off switch 5 and
then release it.
Controlling/Presetting the Stroke Rate
Increasing or reducing the pressure on the
On/Off switch 5 enables stepless stroke-rate
control of the switched-on machine.
Light pressure on the On/Off switch 5 results in
a low stroke rate. Increasing the pressure also
increases the stroke rate.
When the On/Off switch 5 is locked, it is not
possible to reduce the stroke rate.
With the thumbwheel for stroke rate preselec-
tion 4, the stroke rate can be preset and
changed during operation.
The required stroke rate is dependent on the
material and the working conditions and can be
determined by a practical trial.
Reducing the stroke rate is recommended when
the saw blade engages in the material as well as
when sawing plastic and aluminium.
After longer periods of work at low stroke rate,
the machine can heat up considerably. Remove
the saw blade from the machine and allow the
machine to cool down by running it for approx.
3 minutes at maximum stroke rate.
Working Advice
Tips
f When sawing light building materials, ob-
serve the statutory provisions and the rec-
ommendations of the material suppliers.
Note: Do not cover the ventilation slots under-
neath the tool holder with the hand.
Check wood, press boards, building materials,
etc. for foreign objects such as nails, screws or
similar, and remove them, if required.
Switch the machine on and guide it toward the
workpiece. Position the footplate 2 onto the sur-
face of the work and saw through the material
applying uniform contact pressure and feed. Af-
ter completing the working procedure, switch
the machine off.
If the saw blade should jam, switch the machine
off immediately. Widen the gap somewhat with
a suitable tool and pull out the machine.
Plunge Cutting (see figures CD)
f The plunge cutting procedure is only suita-
ble for treating soft materials such as wood,
plaster board or similar! Do not work metal
materials with the plunge cutting proce-
dure!
Use only short saw blades for plunge cutting.
Place the machine with the edge of the footplate
2 onto the workpiece and switch on. For power
tools with stroke speed control, set the maxi-
mum stroke speed. Press the power tool firmly
against the workpiece and allow the saw blade
to slowly plunge into the workpiece.
As soon as the footplate 2 fully lays on the sur-
face of the workpiece, continue sawing along-
side the desired cutting line.
OBJ_BUCH-648-003.book Page 18 Monday, September 14, 2009 10:23 AM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch pfz 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch pfz 600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info