544011

Bosch PFS 3000-2 Manual

22
Zoom out
Zoom in
Previous page
1/274
Next page
22 | English
2 609 007 771 | (28.2.14) Bosch Power Tools
– Pour the spray material into the container 7 up to no more
than the 1000 mark.
– Carry out a test-spray run on a test surface. (see “Spray-
ing”, page 22)
When the spraying pattern is perfect, start the spray job.
or
When the spraying result is not satisfactory or when no paint
comes out, please continue as described under “Correction of
Malfunctions” on page 24.
Starting Operation
Observe the mains voltage! The voltage of the power
source must correspond with the data on the type plate of
the machine.
Pay attention that the base unit cannot draw in dust or
other contamination during operation.
Make sure never to spray on the base unit.
Stop spraying if fluid escapes from places other than
the intended nozzle during spraying, and restore the
spray gun to its proper condition. There is a risk of elec-
tric shock.
Do not direct the fine-spray system against yourself,
other persons or animals.
Switching On (see figure D)
To save energy, only switch the fine-spray system on when
you are using it.
– Check whether the correct nozzle cap is mounted (see
“Changing the Nozzle Cap”, page 21).
– Plug the mains plug into a socket outlet.
– Grasp the spray gun by the handle and point it at the spray
surface.
– Set the sliding switch 24 to the required application to reg-
ulate the air flow (see also “Adjusting the Air Flow”,
page 23).
– Pull the trigger switch 5 on the spray gun.
Note: When the base unit is switched on, air always flows out
at the nozzle .
Switching Off
– Let go of the trigger switch 5 and slide the sliding switch 24
all the way to the left (position ).
– Pull the mains plug from the socket outlet.
Working Advice
Spraying (see figures E –H)
Note: Observe the wind direction when operating the power
tool outdoors.
– Firstly, carry out a test-spray run and adjust the spray pat-
tern and the spray material quantity according to the spray
material. (For adjustments, see the following sections)
– Be absolutely sure to hold the spray gun at a consistent dis-
tance of 20 –25 cm perpendicular to the spray object.
– Begin the spraying procedure outside the target area.
– Move the spray gun evenly cross-wise or up-and-down, de-
pending on the spray pattern setting.
An even surface quality is achieved when the paths overlap
by 4 – 5cm.
– When spraying horizontal objects or spraying overhead,
hold the spray gun at a slight angle and back away from the
sprayed surface.
Risk of stumbling! Pay attention to possible obstacles
in the room.
– Avoid interruptions within the spray surface.
Guiding the spray gun evenly will provide uniform surface
quality.
Non-uniform clearance and spray angle lead to heavy forma-
tion of paint mist and thus to an uneven surface.
– End the spraying procedure outside the target area.
Never completely empty the container for the spray material
by spraying. If the suction tube is no longer immersed in the
spray material, the spray jet will be interrupted and this will
result in an inconsistent surface.
If spray material settles on the air cap 2 or the nozzle cap,
clean the components with the supplied cleaning brush 25.
Adjusting the Spray Pattern (see figure I)
Never actuate the trigger switch 5 while adjusting the
air cap 2.
–Turn the air cap 2 to the requested position.
Adjusting the Spraying Capacity (see figure J)
(PAINTVolume)
– Turn the thumbwheel 4 to set the required spraying capac-
ity:
Settings 1/2/3: “wood” application,
settings 3/4/5: “wall” application.
– Put the spray gun on the container 7. Turn the con-
tainer 7 towards the close symbol until you hear the
lock ring 6 engage.
Air cap Spray jet pattern Application
Vertical flat jet for
horizontal working
direction
Horizontal flat jet
for vertical working
direction
Round jet for cor-
ners, edges and
hard to reach loca-
tions
OBJ_BUCH-2024-002.book Page 22 Friday, February 28, 2014 9:28 AM
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PFS 3000-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PFS 3000-2 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 52,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info