Manual Bosch PFS 105 E WALLPaint (page 19 of 193) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

544062

Zoom out

Zoom in

1/193

English | 19

Bosch Power Tools 1 609 929 Y14 | (23.8.11)

– Clean the nozzle 11 and the nozzle needle with diluting

agent.

From time to time, the nozzle seal 12 must also be cleaned.

– Remove the nozzle 11 and the nozzle seal 12.

If required, use a pointed object, as the nozzle seal is seat-

ed firmly to the spray gun.

– Clean the nozzle seal with diluting agent.

– Reinstall the nozzle seal in the spray gun. Pay attention that

the groove points away from the spray gun.

– Mount the nozzle onto the spray gun body and turn it to the

correct position.

– Mount the air cap 2 onto the nozzle and tighten with the un-

ion nut 3.

Changing the Air Filter (see figure L)

The air filter must be replaced when soiled.

– Remove the air filter cover 21.

– Change the air filter.

– Remount the air filter cover.

Material Disposal

Diluting agent and remainders of spray material must be dis-

posed of in an environmentally-friendly manner. Observe the

manufacturer’s disposal information and the local regulations

for disposal of hazardous waste.

Chemicals harmful to the environment may not be disposed

of into soil, groundwater or bodies of water. Never pour

chemicals harmful to the environment into the sewerage sys-

tem!

Correction of Malfunctions

Problem Cause Corrective Measure

Spray material does not cover

properly

Spraying capacity too low Turn thumbwheel 5 in direction IIII

Clearance to target area too large Reduce spray distance

Not enough spray material on target area,

too few spray paths sprayed over target area

Apply more spray paths over target area

Spray material too viscous Thin down the spray material by 10% again

and carry out a test-spray run

Spray material runs off after

coating

Too much spray material applied Turn thumbwheel 5 in direction I

Clearance to target area too close Increase spray distance

Viscosity of spray material too low Add original spray material

Spray material applied too often over same

spot

Remove spray material; reduce number of

spray paths over same spot

Atomisation too course Spraying capacity too high Turn thumbwheel 5 in direction I

Air flow too low Turn control knob 16 toward the right

Nozzle 11 soiled Clean nozzle

Too little pressure build-up in container 8 Screw container firmly against spray gun

Spray material too viscous Thin down the spray material by 10% again

and carry out a test-spray run

Air filter heavily soiled Changing the Air Filter

Excessive paint mist

Too much spray material applied Turn thumbwheel 5 in direction I

Clearance to spray surface too large Reduce spray distance

Viscosity of spray material too low Reduce air flow; turn control knob 16 toward

the left

Spray jet pulsates Not enough spray material in container Refill spray material

Venting hole on suction tube 10 clogged Clean suction tube and hole

Air filter heavily soiled Changing the Air Filter

Spray material too viscous Thin down the spray material by 10% again

and carry out a test-spray run

Spray material drips from the

nozzle

Build-up of spray material on nozzle 11 and

air cap 2

Clean nozzle and air cap

Nozzle 11 worn Replace nozzle

Nozzle 11 loose Tighten union nut 3

OBJ_BUCH-420-002.book Page 19 Tuesday, August 23, 2011 12:08 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PFS 105 E WALLPaint in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PFS 105 E WALLPaint Manual

Product: