78693
20
Zoom out
Zoom in
Previous page
1/123
Next page
20 | English
1 609 929 S55 | (23.3.09) Bosch Power Tools
Operation
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, press the On/Off switch 2.
To lock the On/Off switch, keep it pressed and
additionally push the lock-on button 3.
To switch off the machine, release the On/Off
switch 2. When the On/Off switch 2 is locked,
press it first and then release it.
Preselecting the Orbital Stroke Rate
With the thumbwheel for preselection of the or-
bital stroke rate 1, you can preselect the required
orbital stroke rate, even during operation.
The required stroke rate depends on the materi-
al and the working conditions and can be deter-
mined through practical testing.
After longer periods of working at low stroke
rate, allow the machine to cool down by running
it for approx. 3 minutes at maximum stroke rate
with no load.
Sanding Plate Brake
An integrated sanding plate brake reduces the
stroke rate when running at no-load so that
scoring is prevented when placing the machine
onto the workpiece.
If the no-load stroke rate continuously increases
over the course of time, then the sanding plate
is damaged and must be replaced or the sanding
plate brake is worn. A worn sanding plate brake
must be replaced by an authorised after-sales
service agent for Bosch power tools.
Working Advice
f Before any work on the machine itself, pull
the mains plug.
f Wait until the machine has come to a stand-
still before placing it down.
Sanding Surfaces
Switch the machine on, place it with the com-
plete sanding surface on the surface to be
worked and move the machine with moderate
pressure over the workpiece.
The removal capacity and the sanding pattern
are mainly determined by the selection of the
sanding sheet, the preselected orbital stroke
rate and the applied pressure.
Only flawless sanding sheets achieve good
sanding capacity and extend the service life of
the machine.
Pay attention to apply uniform sanding pressure;
this increases the working life of the sanding
sheets.
Intensifiying the sanding pressure does not lead
to an increase of the sanding capacity, but to in-
creased wear of the machine and the sanding
sheet.
A sanding sheet that has been used for metal
should not be used for other materials.
Use only original Bosch sanding accessories.
Rough Sanding
Attach a sanding sheet with coarse grain.
Apply only light pressure to the machine so that
it runs at a higher stroke rate and high material
removal is achieved.
Fine Sanding
Attach a sanding sheet with fine grain.
By lightly varying the application pressure or
changing the orbital stroke rate, the sanding
plate stroke rate can be reduced whereby the
orbital action is maintained.
With moderate pressure, move the machine in a
circular pattern or alternately in lengthwise and
crosswise directions over the workpiece. Do not
tilt the machine to avoid sanding through the
workpiece (e.g. when sanding veneer).
After finishing the working procedure, switch
the power tool off.
OBJ_BUCH-969-001.book Page 20 Monday, March 23, 2009 4:07 PM
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PEX 420 AE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PEX 420 AE in the language / languages: Turkish as an attachment in your email.

The manual is 4,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PEX 420 AE

Bosch PEX 420 AE User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 123 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info