533115
13
Zoom out
Zoom in
Previous page
1/52
Next page
13
Cleaning and maintenance
Cleaning
Once the appliance is cool, use a sponge to clean it with soap
and water.
After each use, clean the surface of the respective burner parts
once they have cooled down. If any residue is left (baked-on
food, drops of grease etc.), however little, it will become stuck
to the surface and more difficult to remove later. The holes and
grooves must be clean for the flame to ignite properly.
The movement of some pans may leave metal residue on the
pan supports.
Clean the burners and pan supports using soapy water and
scrub with a non-wire brush.
If the pan supports are fitted with rubber rests, ensure that
these are also cleaned. The rests may come loose and the pan
support may scratch the hob.
Always dry the burners and pan supports completely. Water
droplets or damp patches on the hob at the start of cooking
may damage the enamel.
After cleaning and drying the burners, make sure the burner
caps are correctly positioned on the diffuser.
Caution!
Do not use steam cleaners. This could damage the hob.
If your hob is fitted with a glass or aluminium panel, never use
a knife, scraper or similar implement to clean the point where
it joins the metal.
Maintenance
Always clean off any liquid as soon as it is spilt. This will
prevent food remains from sticking to the hob surface and you
will save yourself any unnecessary effort.
Due to the high temperatures endured, the wok burner and the
stainless steel zones (grease drip tray, burner outline, etc.) can
change colour. This is normal. After each use, clean these
areas with a product that is suitable for stainless steel.
It is recommended that the cleaning product available from our
Technical Assistance Service (code 464524) is used regularly.
Caution!
The stainless steel cleaner must not be used in the area around
the controls. The (printed) symbols may be wiped off.
Do not leave acidic liquids (e.g. lemon juice, vinegar, etc.) on
the hob.
Trouble shooting
Sometimes certain faults detected can be easily resolved.
Before calling the Technical Assistance Service, bear in mind
the following advice:
Fault Possible cause Solution
The general electrical sys-
tem is malfunctioning.
Defective fuse. Check the fuse in the main fuse box and change it
if it is damaged.
The automatic safety switch or circuit breaker has
tripped.
Check the main control panel to see if the auto-
matic safety switch or circuit breaker has tripped.
The automatic switching
on function does not work.
There may be food or cleaning products stuck
between the ignition sparkers and the burners.
The space between the ignition sparker and the
burner must be clean.
The burners are wet. Dry the burner caps carefully.
The burner caps are not correctly positioned. Check that the burner caps are correctly posi-
tioned.
The appliance is not earthed, is poorly connected
or the earthing is faulty.
Contact the installation technician.
The burner flame is not uni-
form.
The burner components are not correctly posi-
tioned.
Correctly place the parts on the appropriate
burner.
The grooves on the burner are dirty. Clean the grooves on the burner.
The gas flow is not normal
or there is no gas.
The gas supply is blocked by gas taps. Open all gas taps.
If the gas is supplied from a gas cylinder, check
that it is not empty.
Change the gas cylinder.
The kitchen smells of gas. A gas tap has been left on. Turn off the taps.
Incorrect coupling of gas cylinder. Check that the coupling is sound.
Possible gas leak. Shut off the gas supply, ventilate the premises and
immediately notify an authorised installation techni-
cian to check and certify the installation. Do not
use the appliance until ensuring that there is no
gas leak in the installation or appliance itself.
The burner immediately
switches off after releasing
the control knob.
The control knob was not held down for long
enough.
Once the burner is on, hold the control knob down
a few seconds longer.
The grooves on the burner are dirty. Clean the grooves on the burner.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PCS875C21N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PCS875C21N in the language / languages: English, German, Dutch, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info