32141
11
Zoom out
Zoom in
Previous page
1/81
Next page
13
EURO • Printed in Germany • BA 1 619 929 477 • PBH 300 E • GB • OSW 11/99
1 619 929 477 • TMS • 27.10.99
Before any work on the machine itself, pull
the mains plug.
With the SDS-plus tool holder, simpler and easier
tool changing is possible without additional aids.
Grease the insertion end of the tool reg-
ularly.
The dust protection cap 1 prevents to a large ex-
tent the entry of drilling dust during operation.
When inserting the tool, take care that the dust
protection cap 1 is not damaged.
If the dust protection cap is damaged, ask
your customer service station to replace it
for you immediately.
It is a requirement of the system that the
SDS-plus tool rotates freely, thereby pro-
ducing a radial eccentricity when the ma-
chine is running at no-load speed.
This does not affect the accuracy of the drill
hole, as the bit is automatically centred dur-
ing drilling.
Inserting
Clean and grease the insertion end of the
tool.
Insert the tool in a twisting manner into the tool
holder until it latches itself. Check the latching by
pulling on the tool.
Removing
Push back the locking sleeve 2 of the tool holder
and remove the tool.
Be careful of hidden electrical
lines or gas and water pipes.
Check the working area, e. g.,
with a metal detector.
Check for correct mains voltage: The voltage
of the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
Switching on: Press the on/off switch 4 and
hold depressed.
Switching off: Release the on/off switch 4.
For low temperatures, the machine reaches
the full hammer/impact performance only
after a certain time.
This start-up time can be shortened by
striking the drill/chisel against the floor one
time.
With the on/off switch 4, the rotational speed/im-
pact rate can be regulated between low and high
speed/rate. Light pressure on the on/off switch 4
results in a low rotational speed/impact rate, for
example, for sensitive work such as hole starting.
With increased pressure, the rotational speed/im-
pact rate is increased.
The machine should not be used without
the auxiliary handle 7.
Loosen the handle by turning to the left. Rotate
the auxiliary handle 7 and adapt to the working
position.
Firmly retighten the handle.
The drilling depth can be set with the depth
stop 8.
The ribbing on depth stop 8 must point upwards.
Changing the Tool
A
B
Initial Operation
Changing the Speed/
Impact Rate
Auxiliary Handle/Depth Stop
PBH 300 E - Buch Seite 13 Montag, 8. November 1999 4:36 16
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PBH300E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PBH300E in the language / languages: English, German, French, Spanish as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PBH300E

Bosch PBH300E User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 109 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info