32137
23
Zoom out
Zoom in
Previous page
1/142
Next page
English | 23
Bosch Power Tools 1 619 929 804 | (16.10.07)
Note: If the tool holder was fully opened to the
stop, a functional ratching sound may be heard
during its next operation and the tool holder will
not close.
In this case, firstly turn the front sleeve 2 in the
opposite direction of the arrow shown in the fig-
ure. Afterwards, the tool holder can be closed
(tightened) again.
Screwdriver bits can be inserted either in com-
mercially available bit holders or directly in the
tool holder.
PBH 240 RE:
Removing Drilling Tools without SDS-plus
(see figure L)
Firmly hold the retaining ring 3 of the quick
change chuck. Open the tool holder by turn-
ing the front sleeve 2 in the direction of the
arrow until the tool can be removed.
Dust/Chip Extraction
Dusts from materials such as lead-containing
coatings, some wood types, minerals and metal
can be harmful to one’s health. Touching or
breathing-in the dusts can cause allergic reac-
tions and/or lead to respiratory infections of the
user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in con-
nection with wood-treatment additives (chro-
mate, wood preservative). Materials containing
asbestos may only be worked by specialists.
Use dust extraction whenever possible.
Provide for good ventilation of the working
place.
It is recommended to wear a P2 filter-class
respirator.
Observe the relevant regulations in your country
for the materials to be worked.
Mounting the Dust Extraction Attachment
(see figure M)
For dust extraction, the dust extraction attach-
ment (accessory) is required. When drilling, the
dust extraction attachment retracts so that the
attachment head is always close to the surface
at the drill hole.
Loosen the wing bolt for depth stop adjust-
ment 19 and remove the depth stop 9.
Insert the dust extraction attachment and
tighten the wing bolt again.
Connect an extraction hose (diameter
19 mm, accessory) to the extraction sleeve
25 of the dust extraction attachment.
The vacuum cleaner must be suitable for the ma-
terial being worked.
When vacuuming dry dust that is especially det-
rimental to health or carcinogenic, use a special
vacuum cleaner.
Adjusting the Drilling Depth on the Dust Ex-
traction Attachment (see figure N)
The required drilling depth X can also be adjust-
ed when the dust extraction attachment is
mounted.
Only for SDS-plus drilling tools:
Insert the SDS-plus drilling tool to the stop into
the SDS-plus tool holder 5. Otherwise, the mov-
ability of the SDS-plus drilling tool can lead to
incorrect adjustment of the drilling depth.
Loosen the wing bolt 29 on the dust extrac-
tion attachment.
Without switching the power tool on, apply it
firmly to the drilling location. The SDS-plus
drilling tool must face against the surface.
Position the the guide pipe 30 of the dust ex-
traction attachment in its holding fixture in
such a manner that the head of the dust ex-
traction attachment faces against the surface
to be drilled. Do not slide the guide pipe 30
further over the telescopic pipe 28 of the
dust extraction attachment than required, so
that as much as possible of the scale 28 on
the telescopic pipe remains visible.
Retighten the wing bolt 29 again. Loosen the
clamping screw
26 on the depth stop of the
dust extraction attachment.
Move the depth stop 27 on the telescopic
pipe 28 in such a manner that the
clearance X shown in the figure corresponds
with the required drilling depth.
Tighten the clamping screw 26 in this posi-
tion.
OBJ_BUCH-495-002.book Page 23 Tuesday, October 16, 2007 3:09 PM
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PBH220RE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PBH220RE in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PBH220RE

Bosch PBH220RE User Manual - English - 142 pages

Bosch PBH220RE User Manual - English - 70 pages

Bosch PBH220RE User Manual - German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish - 142 pages

Bosch PBH220RE User Manual - Spanish - 70 pages

Bosch PBH220RE User Manual - Norwegian, Finnish - 142 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info